doble TDR9000 Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 454

doble TDR9000 Скачать руководство пользователя страница 106

Personnel Safety

4-8

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Personnel Safety

Personnel safety considerations include:

• Hold a pre-test meeting for everyone who will be working in

proximity to the area where testing will be performed. Frequently,
other crews will be working on non-test related tasks in close
proximity to the equipment being tested.

Review:

• Tests to be performed
• Apparatus and the voltage test levels involved
• Potential hazards involved with the work, and the

individual assignments

Remind personnel to be aware of the work activity taking place
around them and be alert to the possibility that non-test personnel
may enter the test area.

• Agree on a consistent and uniform set of visual and verbal signals

that will be used during testing.

• While making the various types of connections involved in the

different tests, it may be necessary for personnel to climb up on
the apparatus.

Be sure that no one remains on the apparatus during the test itself.

N

OTE

Once a test is loaded, never attempt to disconnect the cables from
either the test specimen or from the TDR9000 Instrument until the test
is completed or cancelled.

W

ARNING

Do not handle Contact Monitor cable test connections while a test is
running. Up to 48 VDC can be present.

«
...
104
105
106
107
108
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов