doble TDR9000 Скачать руководство пользователя страница 275 | Manualshive

Страница: 275 / 454

doble TDR9000 Скачать руководство пользователя страница 275

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-75

Monday

, November 26, 2001 1:09 pm

Resistor Contact
Timing Parameters

Figure A.88 shows the Resistor Contact Timing parameters and
specifications available for the circuit breaker resistor contacts.

Figure A.88 Resistor Contact Timing – Parameters and Specifications

Resistor Switch
Timing – Open

The selection can be made, using the Resistor Relative To parameter,
between MAIN and T0 (Test Initiation). This enables the timing of
Resistor Switches relative to the opening of the Main Contacts or test
initiation, respectively.

Parameters include:

Minimum

The minimum time for the Resistor Switch Contacts
to part.

Maximum

The maximum time for the Resistor Switch
Contacts to part.

Figure A.89 shows timing relative to MAIN an T0.

Figure A.89 Opening Time – Resistor Switch

Opening Time

Opening Time

relative to Main (20 ms)

relative to To (40 ms)

«
...
273
274
275
276
277
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов