manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 356 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 356

Trip/Close Fuses

B-28

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

Trip/Close Fuses

Fuses for the Trip and Close coil currents are located on the TDR9000 
Physical Front Panel, as shown in Figure B.19. The status of a Trip/Close 
fuse is determined using the procedure for testing the Trip/Close function 
given in ”Trip/Close Function Test” below.

Figure B.19  Trip/Close Fuses

Trip/Close Function 
Test

The TDR9000 Trip/Close module is monitored during every test. If there 
is an internal electronics problem, a run-time error is reported. These 
run-time tests cannot test the cables, fuses, or the final high current stage 
of the module.

N

OTE

Before running this test, run the Continuity test on the EHV or OCB 
cables.

If a test is run and no errors are reported, and the circuit breaker does not 
operate, this procedure isolates the cause of the failure to the Trip/Close 
fuses or to the Breaker Control cable responsible for the Trip/Close 
function or the Trip/Close module, unless the circuit breaker is defective. 
Fuses can be checked by inspection. The cable can be checked with a 
meter, but this is difficult if the pinout pattern is not known. This makes 
the following procedure the quickest troubleshooting solution:

1.

Connect the alligator clips of the Breaker (Trip/Close) Control cable 
across the test clamps of an activated OCB or EHV cable. 

Trip Fuse

Close Fuse

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов