doble TDR9000 Скачать руководство пользователя страница 269 | Manualshive

Страница: 269 / 454

doble TDR9000 Скачать руководство пользователя страница 269

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-69

Monday

, November 26, 2001 1:09 pm

• F. W. Bell CG-100A clip-on, Hall effect probe, with current

ranges of 10 A and 100 A.

This probe provides 1 V output on both ranges, when current is at
maximum. It is also capable of 100% overload, bringing output
to 2 V.

The Instrument has two current ranges to use with the probe:

• Low – 20 A
• High – 200 A

The following example shows how inappropriately selected current
ranges can give misleading test results. Trip current was measured using
the TDR9000, an external 1 V/10 A shunt and a F. W. Bell CG-100A
clip-on probe with 10 A and 100 A ranges.

Example #1 (Figure A.81)

Ranges selected: Probe - 10 A, TDR9000 - Low (20 A)

Current Monitoring Trip Operation I

shunt

.631 x 10 = 6.31 A

Figure A.81 Current Monitoring Trip Operation

«
...
267
268
269
270
271
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов