doble TDR9000 Скачать руководство пользователя страница 65

Страница: 65 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

2-15

Monday

, November 26, 2001 1:09 pm

Reclose (O-C)

Figure 2.10 is a simplified representation of the test waveform generated
for the Reclose test.

Figure 2.10 Reclose Command Pulse

Command
Parameters

Trip Pulse

This time setting determines the duration of the
Trip Pulse sent to operate the trip circuit of the
circuit breaker.

Close Pulse

This pulse, initiated after the Trip Pulse, operates
the close circuit and performs the Reclose function.

Reclose and Delay

These parameters determine when the Close Pulse
is initiated:

Standing

Initiates a Close .5 cycles (8.3 ms at 60 Hz) after
the test starts. This occurs when

Standing

selected in the

Reclose

field.

Delay

Initiates a Close after the time entered in the

Delay

Length

field that appears when

Delay

is selected in

the

Reclose

field.

Recording Length

This setting determines the recording length and
implicitly sets the sampling rate at which the
recording is performed.

66 msecs

Trip Command
Close Command

Delay

Off

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 65 / 454

Результаты поиска

Содержание TDR9000

Отзывы: