doble TDR9000 Скачать руководство пользователя страница 432

Страница: 432 / 454

Universal Adapter

I-22

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Table I.2 lists specifications for the universal adapter.

Table I.2 Specifications: Universal Adapter

Specification

Values

Closing

At normal pressure, the time from energizing of the pilot valve coil
to contact touch is 7.0 to 7.25 cycles (117 to 121 ms)

Opening Contact Velocity

The average contact velocity measured between 1" and 2½" from
the full closed position is 26 to 30 f/s.

Opening Time

• Control voltage at the nominal value
• The time from energizing the trip coils to main contact part is 1.30

cycles or less (2 ms)

• Contact travel at .5 of a cycle after contact part is a minimum of

3.4" from the fully closed position

• The contact travel at .9 of a cycle after contact part is less than

5.3" from the fully closed position

Close to Open Operation

On a close to open operation the auxiliary switch will energize the
trip coil at contact touch

.15 cycle (2.5 ms)

Synchronizing Time

• Maximum spread of the three poles on closing .25 cycles (4 ms)
• Maximum spread of the three poles on opening contact part

.15 cycles (2.5 ms)

Crossarm rotation

• Angular travel of Crossarm is 35.5

• Crossarm length is 12.75"
• Travel measured with Westinghouse adapter is 7.899" (arc length).

Travel measured with Doble adapters and transducers according
to drawing 03D-1025

• Crossarm rotation 35.5

, adapter lever rotates 46

• Angular travel ratio is 46/35.5 = 1.296. 30% difference

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 432 / 454

Результаты поиска

Содержание TDR9000

Отзывы: