doble TDR9000 Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 454

doble TDR9000 Скачать руководство пользователя страница 118

Linear Transducer and Rotary Attachments

4-20

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Linear Motion

To configure for linear motion:

1.

Remove the Chuck Holder Plate from the Transducer by loosening
the two captive screws.

2.

If the Rotary Chuck is:

• Mounted to the Rotary Shaft, proceed to step 3
• Otherwise, proceed to step 6

3.

Position the wrench portion of the Chuck Holder Plate on the Rotary
Shaft (see Figure 4.6 on page 4-18).

4.

Rotate the Rotary Chuck counterclockwise and remove it from the
Rotary Shaft.

Utilize the Chuck Key, if necessary, as described in step 6 of the
previous procedure.

5.

Store the Rotary Chuck on the Chuck Holder Plate as shown in
Figure 4.5 on page 4-17.

N

OTE

If the Rotary Chuck is mounted on the Rotary Shaft during a linear
measurement, the added mass of the chuck can induce internal slippage
to the transducer causing measurement error.

6.

Mount the Chuck Holder Plate in the LINEAR position on the
Transducer (Figure 4.8) using the two captive screws to secure it.

Configuration is complete.

«
...
116
117
118
119
120
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов