doble TDR9000 Скачать руководство пользователя страница 283 | Manualshive

Страница: 283 / 454

doble TDR9000 Скачать руководство пользователя страница 283

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-83

Monday

, November 26, 2001 1:09 pm

Example:

To measure Contact Wipe on the contact labeled phase A (Figure A.96):

• Mount the transducer on the phase A tank.
• Connect the Transducer Cable to the first channel on the

Motion/OCB module.

• Activate Motion Channel 1 on the Test Plan tab and label it A.
• Connect Contact Monitor Cable 1 to phase A.
• Set the Expected, Plus and Minus specifications in the Contact

Wipe parameter portion of the Travel Specifications on the Test
Plan tab.

Figure A.96 Contact Wipe Measurement

For an EHV Circuit Breaker (module type), the Instrument determines
wipe for activated Contact 1 of the phase that has a corresponding
activated Motion Channel and a Transducer connected to it. Phase A
always corresponds to Motion Channel 1, Phase B to Motion Channel 2,
Phase C to Motion Channel 3.

Contact #!

Contact #2

Contact #3

Contact #1 Wipe

Total

Travel

Travel #1

«
...
281
282
283
284
285
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов