doble TDR9000 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 454

doble TDR9000 Скачать руководство пользователя страница 105

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-7

Monday

, November 26, 2001 1:09 pm

Safety

This section discusses principles that must be followed to ensure a safe
testing environment.

Instrument Precautions

• Do not drop or throw the Instrument or transducers.
• Do not use the Instrument or transducers as a step or platform.
• Do not store the Instrument or transducers in temperatures lower

than –13

°

F (–25

°

C) or greater than +158

°

F (+70

°

C).

• Do not operate the Instrument or transducers in temperatures

lower than 32

°

F (0

°

C) or greater than +122

°

F (+50

°

C).

• Do not store the Instrument or transducers in excessively humid

environments.

• Do not expose the Instrument or transducers to rain, snow, sand,

or dust.

• Always transport the Instrument or transducers with their

protective covers in place.

Testing Personnel Required

The TDR9000 should not be operated by a crew of less than two people.
Designate one person as the

Test Set Operator,

and the other as the

Safety Observer.

The role of testing personnel can be defined as follows:

Test Set Operator

Supervises the test and operates the TDR9000
using the Safety cable switch provided.

Safety Observer

Observes the performance of the test, oversees the
test setup, watches for any potential safety hazards,
and gives warnings and guidance as required.

«
...
103
104
105
106
107
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов