doble TDR9000 Скачать руководство пользователя страница 387 | Manualshive

Страница: 387 / 454

doble TDR9000 Скачать руководство пользователя страница 387

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

D-5

Monday

, November 26, 2001 1:09 pm

Results Processing

TRXField receives the test data and decompresses it. Calculations are
performed on a channel by channel basis resulting in switching times,
maximum values, and average values during specific times. The results of
these calculations are then compared to specifications either received as
part of a Test Plan or entered manually by the user prior to the test. A
Pass/Fail comparison is performed and the results are reported on all
channels with specifications.

Results are made available in both tabular and graphical formats.
Numerous utilities such as zooming, overlaying, and on screen
measurements are made available as part of the graphics package.

Self-Test

The Instrument has a Self-Diagnostics test, comprised of two individual
tests, which functionally test the operation of all measurement channels.
No Trip or Close command signals are output from the Instrument during
the Self-Diagnostic test.

Once the test is initiated from the Virtual Front Panel, the first test, the
Global Self-Test begins. Each measurement channel is disconnected from
the external connector via relays. This allows the entire Self-Diagnostics
test to run without disconnecting the Instrument test setup. Simulated
signals are injected just inside the Physical Front Panel and sampled as if
a standard test was under way. The results are interpreted by the
TRXField software and compared to expected results. If all channels are
functioning properly, the test ends. If a functional failure is detected, the
second test begins, the Local Self-Test, which continues testing with the
measurement channels disconnected between the Physical Front Panel
modules and the measurement cards in the card cage. Again, test signals
are injected and the results interpreted. Logic is applied to the two Test
Results and the failed card or module is identified and displayed.

«
...
385
386
387
388
389
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов