doble TDR9000 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 454

doble TDR9000 Скачать руководство пользователя страница 60

System

2-10

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Triggers

The TDR9000 comes with Trigger Input and Trigger Output capabilities.

Trigger Input

Trigger Input has three possible sources, selected in the Trigger Source
field, that begin recordings:

None(Internal)

AUX Contact

An input that comes in through an Auxiliary
Contact triggers the test.

Trigger In

An input that comes in through the Trigger In
connection of the System module and is
conditioned by a delay time, starts the TDR9000
test.

Trigger Output

Trigger Output enables the user to operate a circuit breaker using an
input generated by the TDR9000, as connected through the Trigger Out
connectors of the System module.

Serial Interface

Serial communication is via the electrically-isolated PC RS-232
connection and the RS-232 connection on the IBM compatible laptop.
The baud rate of this connection is set at 38.4 kbits/sec. Doble supplies a
twenty-five foot, double-shielded cable for connecting this interface.

Printer

The TDR9000 can be ordered with a Pentax



PocketJet II

™

thermal

printer. The printer provides print outs of Test Plans, tabular results and
graphical results in the field. For easy storage and transport, the printer is
mounted in the Instrument cover. When in use, the printer is connected
to the PC’s parallel port.

«
...
58
59
60
61
62
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов