doble TDR9000 Скачать руководство пользователя страница 115

Страница: 115 / 454

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

4-17

Monday

, November 26, 2001 1:09 pm

The Chuck Holder Plate is shipped in two different configurations, as
shown in Figure 4.5. This plate provides five different functions:

• When mounted in the ROTARY position

• It depresses a micro-switch that indicates to the TDR9000 that

a rotary measurement is being performed.

• It covers the gate area, which serves as a reminder that it must

be moved to the LINEAR position prior to inserting the travel
rod to perform a linear measurement.

• It includes a metal sheath that covers the Rotary Shaft to ensure

that the threads do not come in contact with any foreign objects
that could cause thread damage during storage or operation.

• It has a cutout that is used as a wrench to hold the Rotary Shaft,

while the Rotary Chuck is loosened or tightened.

• It provides a storage location for the Rotary Chuck when a linear

measurement is made.

Figure 4.5 Chuck Holder Plate Configuration

Version 2

Version 1

Chuck Key

Sheath

Rotary Chuck in

Captive

Chuck Key

Rotary Chuck in

Captive

Sheath

Wrench

Captive

Storage Location

Wrench

Screws

Storage Location

Screw

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 115 / 454

Результаты поиска

Содержание TDR9000

Отзывы: