doble TDR9000 Скачать руководство пользователя страница 403

Страница: 403 / 454

72A-1898 Rev. A 11/01

H-1

Monday

, November 26, 2001 1:09 pm

Appendix H. TDR9000

™

Circuit Breaker Test

System Specifications

This appendix details specifications for the TDR9000 and its operations
in the following areas:

• OCB/Motion module
• EHV module
• Event module
• System module
• Physical
• Environmental

OCB/Motion

Table H.1 lists the characteristics of the OCB/Motion module.

Table H.1 OCB/Motion Module

Characteristic

Description

OCB

Main Contact Channels

3 channels with 1 break per phase

Contact Sense Voltage for
Main Contact Timing

48/15/7.5 VDC
(Modified by pre-insertion resistor value)

Contact Sense Voltage for
Resistor Switch Timing

48/15/7.5 VDC
(Modified by pre-insertion resistor value)

Close and Open Timing
Resolution

100 microseconds

Close and Open Timing
Accuracy

100 microseconds

Minimum Contact Bounce
Measurement

60 microseconds

Pre-Insertion Resistor
Value Range

10 - 400 Ohms or 300 - 7000 Ohms

Содержание TDR9000







































































































































































































































































































































































































































































Результаты поиска

Содержание TDR9000

Отзывы:

doble TDR9000, Руководство пользователя, Страница: 403 / 454

Результаты поиска

Содержание TDR9000

Отзывы: