manualshive.com logo in svg

doble TDR9000, Руководство пользователя, Страница: 228 / 454

Поделиться
Скачать
doble TDR9000 Скачать руководство пользователя страница 228

TRX

™

/TRXField

™

 and the Circuit Breaker Test Plan

A-28

72A-1898   Rev. A    11/01

Monday

, November 26, 2001 1:09 pm

During the measurement of contact wipe, the measurement starts when 
the moving contact makes an electrical contact with the stationary 
contact and ends when the moving contact stops (Figure A.30).

Figure A.30  Contact Penetration Measurement Endpoints

Figure A.29 on page A-27 and Figure A.30 show that due to the chamfer 
on the moving contact, the mechanical and electrical measurements may 
yield different results.

Before the manufacturer’s specification is used, it is important to know 
how this value is obtained. If the only specification available is the result 
of mechanical measurement, the benchmark for future trending analysis 
should be obtained using the TDR9000.

TDR9000

™

 TRXField

™

 Software and Test Plan Dynamics

The main body of this guide explained the procedures for operating the 
TDR9000, including the mechanics for creating or using existing Test 
Plans. This section describes the effect that changing Test Plan fields has 
on running a test. It does so by relating individual Test Plan items to the 
physical components they affect in the field.

TRX

™

/TRXField

™

 and the Circuit Breaker Test Plan

The TRX software, comprised of TRX and TRXField, facilitates the 
creation of Circuit Breaker Test Plans, analysis of test data, and storage of 
Circuit Breaker test data. The TDR9000 operates using only the TRXField 
portion of the software. The Test Plan can be created using either of these 
programs and is the key to simplifying circuit breaker testing. By creating 
a Test Plan, the time-consuming work of entering repetitive circuit 
breaker ID information and test parameters is eliminated. Once this data 
has been entered, it is saved in the Test Plan on a floppy diskette for reuse 
later.

Measurement

starts

Wipe

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов