doble TDR9000 Скачать руководство пользователя страница 227 | Manualshive

Страница: 227 / 454

doble TDR9000 Скачать руководство пользователя страница 227

TDR9000

™

Circuit Breaker Test System User’s Guide

72A-1898 Rev. A 11/01

A-27

Monday

, November 26, 2001 1:09 pm

Contact Penetration, Insertion, and Wipe

The main distinction between the contact penetration, sometimes
referred to as contact insertion, and the contact wipe is that the first is
obtained through mechanical measurement and the second through
electrical measurement.

The value of contact penetration is obtained as follows: with the circuit
breaker closed, a mark is made on the moving contact as shown in
Figure A.28.

Figure A.28 Contact Penetration Value Preparation

With the circuit breaker open, the distance between the mark and the top
of the moving contact is measured as shown in Figure A.29. This distance
is the value of contact penetration or contact insertion.

Figure A.29 Contact Penetration Measurement

Mark

Penetration

Mark

«
...
225
226
227
228
229
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов