doble TDR9000 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 454

doble TDR9000 Скачать руководство пользователя страница 102

Connecting the TDR9000

™

4-4

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Configuring Analog/Auxiliary Channels for First Trip/Close Tests

Connecting leads for a First Trip/Close test consist of:

• TDR9000 Connections
• Circuit Breaker Connections

Connecting the TDR9000

™

Table 4.1 and Table 4.2 list the connections to the TDR9000 required
for a minimum set of channels and a recommended set of channels,
respectively. Since this is an external trigger test, no control cables are
used.

*Connect to an Event module if using Aux Contact trigger source, and to
the Trigger In jacks on the System module if using the Trigger In source.

Table 4.1 TDR9000

™

Using a Minimum Set of Channels

Item

Signal

Type

TDR9000 Module
Connection

1

Main Contact
(from CT secondary)

Analog

Event

2

Trip relay coil
current

Analog

Event

3

DC Supply voltage

Analog

Event

4

52CS/T contact state
(for Trigger In source)

Auxiliary Contact Event or Trigger In*

«
...
100
101
102
103
104
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов