doble TDR9000 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 454

doble TDR9000 Скачать руководство пользователя страница 168

Configuring Test Plans

4-70

72A-1898 Rev. A 11/01

Monday

, November 26, 2001 1:09 pm

Using the Pretest Checklist

Use the checklist given in Table 4.8 to ensure that the system is safely
configured for testing. Once this Pretest Checklist is complete, DC power
can be restored to the circuit breaker Trip and Close circuits, and
AC power can be applied to the Instruments.

Table 4.8 Pretest Checklist

Item

✔

Circuit breaker under test is removed from service according to
government and company safety rules (Not applicable to First
Trip/Close tests)

A Safety Ground cable is installed on the TDR9000

Proper AC power is available

One end of each phase of the circuit breaker is grounded (Not
applicable to First Trip/Close tests)

All cables are connected to the TDR9000

Transducer Connecting Rod is coupled to the circuit breaker
rod (Not applicable to First Trip/Close tests)

Rotary Attachment is installed (optional- not applicable to First
Trip/Close tests)

All Motion Transducer cables are connected to the transducer
(Not applicable to First Trip/Close tests)

All Contact Monitor cables are connected to the circuit breaker
bushings (Not applicable to First Trip/Close tests)

All test parameters are configured via the Virtual Front Panel or
Test Plan

All the current probes are zeroed (if used)

«
...
166
167
168
169
170
...
»

Содержание TDR9000







































































































































































































































































































































































































































































Отзывы:

Нет отзывов