Stratasys uPrint, Service Manual, Page: 284 / 383

uPrint/uPrint SE Service Manual 6-17
14,48 Abort : Vertex command error. 1. If this message is displayed on LCD ONLY, possible memory problem,
replace SBC. If this message is not displayed on the LCD, (seen in cfg
file), RAM is NOT the root cause.
2. If the frequency of the error is greater than once every three months,
replace the controller board.
14,49 Internal : PCode Error, Bad
Curve.
This error will not be displayed. Software development use only.
14,50 Internal : PCode Error, DY
within curve.
This error will not be displayed. Software development use only.
14,51 Abort : Model material not
loaded.
14,52 Abort : Support material not
loaded.
14,53 Abort : Model head motor not
ready.
14,54 Abort : Support head motor
not ready.
1. Reload material.
Note: System is not recognizing that material is loaded.
14,55 Abort : Find home failed, X
home and X eot both on
14,56 Abort : Find home failed, Y
home and Y eot both on
1. Power cycle machine - remember to move head away from switches.
2. X errors - Check pins and re-seat connector J505 on the I/O Board. Y
errors - Check pins and re-seat connector J503 on the I/O Board.
3. Using LED's check to see if switch state toggles. If not, check sensor
and/or umbilical cable for X and Y cable for Y.
4. Replace the head board for X errors and replace the Y sensors for Y.
14,57 Abort : Find home failed, X
home time-out
14,58 Abort : Find home failed, Y
home time-out
1. Power cycle machine - remember to move head away from switches.
2. If chatter in motor, check motor and/or motor cable for Y, umbilical
cable for X.
3. Check for obstacles obstructing X or Y movement.
4. Using LED's check to see that the state changes when sensor is
activated. If not, check sensor and/or umbilical cable for X and Y
cable for Y.
14,59 Abort : Find home failed, X
home not tripped
14,60 Abort : Find home failed, Y
home not tripped
1. Power cycle machine - remember to move head away from switches.
2. Using LED's check to see home LEDs toggles when sensor is activated. If
not, check sensor and/or Umbilical Cable for X and Y cable for Y.
3. X errors - Check pins and re-seat connector J505 on the I/O Card. Y
errors - Check pins and re-seat connector J503 on the I/O Card.
14,61 Abort : Find home failed, X
home tripped
14,62 Abort : Find home failed, Y
home tripped
1. Power cycle machine - remember to move head away from switches.
2. Using LED's/test points: Check to see home box toggles when sensor is
activated. If not, check sensor and/or umbilical cable for X , Y cable
for Y.
3. X errors - Check pins and re-seat connector J505 on the I/O Card. Y
errors - Check pins and re-seat connector J503 on the I/O Card.
14,63 Abort : Find home failed, X eot
tripped
14,64 Abort : Find home failed, Y eot
tripped
1. Power cycle machine - remember to move head away from switches.
2. Using LED's check to see home box toggles when sensor is activated. If
not, check sensor and/or umbilical cable for X , Y cable for Y.
3. X errors - Check pins and re-seat connector J505 on the I/O Card. Y
errors - Check pins and re-seat connector J503 on the I/O Card.
14,65 Abort : Find home failed, X eot
not tripped
14,66 Abort : Find home failed, Y eot
not tripped
1. Power cycle machine - remember to move head away from switches.
2. Using LED's check to see home box toggles when sensor is activated. If
not, check sensor and/or umbilical cable for X , Y cable for Y.
3. X errors - Check pins and re-seat connector J505 on the I/O Card. Y
errors - Check pins and re-seat connector J503 on the I/O Card.
14,67 Abort : Head temperature too
high
1. Verify the TC and Liquefier Heaters are plugged in properly.
2. Check umbilical is connected properly.
3. TC Amp board is bad. Replace TC Amp Board.
4. Head Board is bad. Replace Head Board.
5. Replace the umbilical cable.
14,68 Abort: Illegal PMD Command 1. If error occurs more than once a month replace the controller board.
Code Description Corrective Actions