656
YASKAWA
SIEPC71061723A YASKAWA AC Drive CR700 Technical Manual
Note:
When
F1-33 = 0
or
F1-34 = 0
, the gear ratio is 1.
■
F1-34: Encoder 2 Gear Teeth 2
No.
(Hex.)
Name
Description
Default
(Range)
F1-34
(03B3)
Encoder 2 Gear Teeth 2
Sets the number of gear teeth on the load side for motor 2. This parameter and
F1-33 [Encoder 2
Gear Teeth 1]
set the gear ratio between the motor and encoder.
0
(0 - 1000)
After you set the number of gear teeth, the drive uses this formula to calculate the motor speed:
Note:
When
F1-33 = 0
or
F1-34 = 0
, the gear ratio is 1.
■
F1-35: Encoder 2 Pulse Monitor Scaling
No.
(Hex.)
Name
Description
Default
(Range)
F1-35
(03BE)
Encoder 2 Pulse Monitor
Scaling
Sets the dividing ratio for monitor signals output from the encoder option. This parameter is for
motor 2.
001
(001 - 032, 102 - 132 (1 - 1/
32))
The dividing ratio = (1 + x)/yz when the setting value is a 3-digit value (xyz).
For example, the dividing ratio is 1/32 when
F1-35 = 032
.
Note:
The dividing ratio for the monitor signal is 1:1 when using a single-pulse encoder.
■
F1-36: Encoder 2 PCB Disconnect Detect
No.
(Hex.)
Name
Description
Default
(Range)
F1-36
(03B5)
Encoder 2 PCB Disconnect
Detect
Sets the function that enables and disables detection of a disconnected PG-X3 encoder connection
cable.
PGoH [Encoder (PG) Hardware Fault]
is detected when this parameter is enabled. This
parameter is for motor 2.
1
(0, 1)
0 : Disabled
1 : Enabled
■
F1-37: Encoder 2 Signal Selection
No.
(Hex.)
Name
Description
Default
(Range)
F1-37
(03BD)
Encoder 2 Signal Selection
Sets the number of channels for the signal to the encoder option. This parameter is for motor 2.
0
(0, 1)
0 : A Pulse Detection
1 : AB Pulse Detection
◆
F2: Analog Input Option
F2 parameters
set the operation of the drive when you use analog input option card AI-A3. The AI-A3 card has 3
input terminals that accept voltages of -10 V to +10 V (20 kΩ) or currents of 4 mA to 20 mA (250 Ω). Install the
AI-A3 card to enable setting very accurate analog references with high resolution.
Refer to the AI-A3 option manual for more information about how to install, wire, and set the AI-A3 card.
WARNING!
Sudden Movement Hazard. Do test runs and examine the drive to make sure that the command references are
correct. If you set the command reference incorrectly, it can cause damage to the drive or serious injury or death.
V/f
CL-V/f
OLV
CLV
AOLV
V/f
CL-V/f
OLV
CLV
AOLV
V/f
CL-V/f
OLV
CLV
AOLV
V/f
CL-V/f
OLV
CLV
AOLV
Содержание CR700
