Dell S6100 Скачать руководство пользователя страница 797

Страница: 797 / 1743

ICMP unreachables are not sent

IP unicast RPF check is not supported

Dell#

Dell# show ip interface

port-channel

128

Port-channel 128 is down, line protocol is down

Internet address is 10.1.1.1/16

Broadcast address is 10.1.255.255

Address determined by user input

IP MTU is 1500 bytes

Directed broadcast forwarding is disabled

Proxy ARP is enabled

Split Horizon is enabled

Poison Reverse is disabled

ICMP redirects are not sent

ICMP unreachables are not sent

IP unicast RPF check is not supported

Dell#

Dell#show ip interface

vlan

Vlan 1 is down, line protocol is down

Internet address is not set

IP MTU is 1500 bytes

Directed broadcast forwarding is disabled

Proxy ARP is enabled

Split Horizon is enabled

Poison Reverse is disabled

ICMP redirects are not sent

ICMP unreachables are not sent

IP unicast RPF check is not supported

Dell#

Usage Information

The following describes the

show ip interface brief

command shown in the following example.

Fields

Description

Interface

Displays type of interface and the associated slot and port number.

IP-Address

Displays the IP address for the interface, if configured.

Ok?

Indicates if the hardware is functioning properly.

Method

Displays “Manual” if the configuration is read from the saved configuration.

Status

States whether the interface is enabled (up) or disabled (administratively down).

Protocol

States whether IP is enabled (up) or disabled (down) on the interface.

Example (Brief)

Dell# show ip interface brief

Interface IP-Address OK? Method Status Protocol

TenGigabitEthernet 1/1/1/1 unassigned NO Manual administratively down down

TenGigabitEthernet 1/1/1/2 unassigned NO Manual administratively down down

TenGigabitEthernet 1/1/1/3 unassigned YES Manual up up

TenGigabitEthernet 1/1/1/4 unassigned YES Manual up up

TenGigabitEthernet 1/1/2/1 unassigned YES Manual up up

TenGigabitEthernet 1/1/2/2 10.10.10.1 YES Manual up up

TenGigabitEthernet 1/1/2/3 unassigned NO Manual administratively down down

IPv4 Routing

797

Содержание S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды

Dell S6100, Руководство по настройке

Результаты поиска

Содержание S6100

Отзывы:

Похожие инструкции для S6100

Бренды по названию

Популярные бренды