Dell S6100 Скачать руководство пользователя страница 1638 | Manualshive

Страница: 1638 / 1743

background image

VLAN Stacking

With the virtual local area network (VLAN)-stacking feature (also called stackable VLANs and QinQ), you can “stack” VLANs into one
tunnel and switch them through the network transparently.
The Dell Networking OS supports this feature.

For more information about basic VLAN commands, see the

Virtual LAN (VLAN) Commands

Important Points to Remember

•

If you do not enable the spanning tree protocol (STP) across the stackable VLAN network, STP bridge protocol data units (BPDUs)

from the customer’s networks are tunneled across the stackable VLAN network.

•

If you do enable STP across the stackable VLAN network, STP BPDUs from the customer’s networks are consumed and not tunneled

across the stackable VLAN network unless you enable protocol tunneling.

NOTE:

For more information about protocol tunneling on the E-Series, see

Service Provider Bridging

.

•

Layer 3 protocols are not supported on a stackable VLAN network.

•

Assigning an IP address to a stackable VLAN is supported when all the members are only stackable VLAN trunk ports. IP addresses on

a stackable VLAN-enabled VLAN are not supported if the VLAN contains stackable VLAN access ports. This facility is provided for the

simple network management protocol (SNMP) management over a stackable VLAN-enabled VLAN containing only stackable VLAN

trunk interfaces. Layer 3 routing protocols on such a VLAN are not supported.

•

Dell Networking recommends that you do not use the same MAC address, on different customer VLANs, on the same stackable VLAN.

•

Interfaces configured using stackable VLAN access or stackable VLAN trunk commands do not switch traffic for the default VLAN.

These interfaces are switch traffic only when they are added to a non-default VLAN.

•

Starting with Dell Networking OS version 7.8.1 for C-Series and S-Series (Dell Networking OS version 7.7.1 for E-Series, 8.2.1.0 for E-

Series ExaScale), a vlan-stack trunk port is also allowed to be configured as a tagged port and as an untagged port for single-tagged

VLANs. When the vlan-stack trunk port is also a member of an untagged vlan, the port must be in Hybrid mode. For more information,

portmode hybrid

Topics:

•

•

•

•

•

stack-unit module

•

vlan-stack access

•

vlan-stack compatible

•

vlan-stack dot1p-mapping

•

vlan-stack protocol-type

•

vlan-stack trunk

57

1638

VLAN Stacking

«
...
1636
1637
1638
1639
1640
...
»

Содержание S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S6100

Бренд: La Toulousaine Страницы: 6

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

SilverStorm 9000

Бренд: Qlogic Страницы: 50

Бренд: Little Giant Страницы: 2

Бренд: N-Tron Страницы: 158

Бренд: Vega Страницы: 36

IES8242MPp9H-S-DR

Бренд: OTS Страницы: 3

CheetaHub Classic-2041

Бренд: Accton Technology Страницы: 7

CT-HDVD-4X14K-SW

Бренд: NB Страницы: 23

Бренд: Allied Telesis Страницы: 56

Бренд: A-Neuvideo Страницы: 20

Бренд: Quark-Elec Страницы: 10

GIGAswitch GSR-16

Бренд: Cabletron Systems Страницы: 346

Бренд: Veris Industries Страницы: 2

Бренд: Arista Страницы: 38

7020SR-32C2 Series

Бренд: Arista Страницы: 42

Бренд: ABB Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды