ping
Test connectivity between the system and another device by sending echo requests and waiting for replies.
Syntax
ping [
host
|
ip-address
|
ipv6-address
] [count {
number
| continuous}]
[
datagram-size
] [
timeout
] [
source (ip src-ipv4-address)
|
interface
] [
tos
] [
df-
bit (y
|
n)
] [
validate-reply(y
|
n)
] [
outgoing-interface
] [
pattern pattern
] [
sweep-
min-size
] [
sweep-max-size
] [
sweep-interval
] [
ointerface (ip src-ipv4-address)
|
interface
] [
ethernet
| vrf
vrf-name
]
Parameters
host
(OPTIONAL) Enter the host name of the devices to which you are testing connectivity.
ip-address
(OPTIONAL) Enter the IPv4 address of the device to which you are testing connectivity.
The address must be in the dotted decimal format.
ipv6-address
(OPTIONAL) Enter the IPv6 address, in the x:x:x:x::x format, to which you are testing
connectivity.
NOTE:
The :: notation specifies successive hexadecimal fields of zeros.
count
Enter the number of echo packets to be sent. The default is
5
.
•
number: from 1 to 2147483647
•
continuous: transmit echo request continuously
datagram size
Enter the ICMP datagram size. The range is from 36 to 15360 bytes. The default is
100
.
timeout
Enter the interval to wait for an echo reply before timing out. The range is from 0 to 3600
seconds. The default is
2 seconds
.
source
Enter the IPv4 or IPv6 source ip address or the source interface. For IPv6 addresses, you
may enter global addresses only. Enter the IP address in A.B.C.D format.
•
For a 10-Gigabit Ethernet interface, enter the keyword
TenGigabitEthernet
then
the stack/slot/port/subport information.
•
For a 25-Gigabit Ethernet interface, enter the keyword
twentyFiveGigE
then the
stack/slot/port/subport information.
•
For a 40-Gigabit Ethernet interface, enter the keyword
fortyGigE
then the stack/
slot/port[/subport] information.
•
For a 50-Gigabit Ethernet interface, enter the keyword
fiftyGigE
then the stack/
slot/port/subport information.
•
For a 100-Gigabit Ethernet interface, enter the keyword
hundredGigE
then the
stack/slot/port information.
•
For a port channel interface, enter the keywords
port-channel
then a number.
•
For a VLAN interface, enter the keyword
vlan
then a number from 1 to 4094.
•
For a Tunnel interface, enter the keyword
tunnel
then a number from 1 to 16383.
tos
(IPv4 only) Enter the type of service required. The range is from 0 to 255. The default is
0
.
df-bit
(IPv4 only) Enter
Y
or
N
for the “don't fragment” bit in IPv4 header.
•
N
: Do not set the “don't fragment” bit.
•
Y
: Do set “don't fragment” bit
116
Control and Monitoring
Содержание S6100
Страница 1: ...Dell Command Line Reference Guide for the S6100 ON System 9 11 2 0P1 ...
Страница 474: ...protocol list ttl0 ttl1 Dell 474 Control Plane Policing CoPP ...
Страница 979: ... show lldp neighbors display the LLDP neighbors Link Layer Discovery Protocol LLDP 979 ...
Страница 1627: ... uplink state group creates an uplink state group and enables the tracking of upstream links Uplink Failure Detection UFD 1627 ...