Kollmorgen AKD PDMM series User Manual Download Page 126

Page: 126 / 513

AKD PDMM User Guide | 14.3 Summary of Parameters and Commands

Parameter or Command

Type

Description

FBUS.SYNCDIST (pg 338)

Sets time target for synchronization.

FBUS.SYNCWND (pg
339)

Sets symmetrically arranged window around the desired sync
distance.

FBUS.TYPE (pg 339)

R/O

Shows the active fieldbus type.

Hardware Limit Switch
(HWLS)

HWLS.NEGSTATE (pg
347)

R/O

Reads the status of the negative hardware limit switch.

HWLS.POSSTATE (pg
347)

R/O

Reads the status of the positive hardware limit switch.

Current Loop (IL)

IL.BUSFF (pg 349)

R/O

Displays the current feedforward value injected by the fieldbus.

IL.CMD (PG 349)

R/O

Reads the value of the q-component current command.

IL.CMDU (PG 349)

R/W

Sets the user current command.

IL.DIFOLD (PG 350)

R/O

Reads the drive foldback current limit.

IL.FB (PG 351)

R/O

Reads the actual value of the d-component current.

IL.FBSOURCE (pg 351)

R/W

Sets the feedback source for the current loop. Only applies
when MOTOR.TYPE = 4.

IL.FF (pg 352)

R/O

Displays the current loop overall feedforward value.

IL.FOLDFTHRESH (PG
352)

Reads the foldback fault level.

IL.FOLDFTHRESHU (pg
353)

Sets the user value for the foldback fault level.

IL.FOLDWTHRESH (PG
353)

Sets the foldback warning level.

IL.IFOLD (pg 355)

R/O

Reads the overall foldback current limit.

IL.IUFB (PG 355)

R/O

Reads the sigma-delta measured current in the u-winding of the
motor.

IL.KACCFF (pg 356)

R/W

Sets current loop acceleration feedforward gain value

IL.KBUSFF (pg 357)

R/W

Current loops fieldbus injected feed-forward gain

IL.KP (PG 357)

Sets the proportional gain of the q-component of the PI reg-
ulator.

IL.KPDRATIO (PG 358)

Sets the proportional gain of the d-component current PI-reg-
ulator as a percentage of IL.KP

IL.KPLOOKUPINDEX (pg
358)

R/W

Sets the index into the Current Loop Gain Scheduling Table.

IL.KPLOOKUPVALUE (pg
359)

R/W

Sets the value of the current loop gain scheduling index.

IL.KPLOOKUPVALUES
(pg 359)

R/W

Gets the Current Loop Gain Scheduling Table.

IL.KVFF (pg 360)

R/W

Current loop velocity feed-forward gain.

IL.LIMITN (PG 360)

Sets the negative user (application-specific) current limit.

IL.LIMITP (PG 361)

Sets the positive user (application-specific) current limit.

IL.MFOLDD (PG 362)

Sets the motor foldback maximum time at motor peak current.

IL.MFOLDR (PG 362)

R/O

Sets the motor foldback recovery time.

Kollmorgen™ | December 2012

126

Summary of Contents for AKD PDMM series


































































































































































































































































































































































































































































































































Search results

Summary of Contents for AKD PDMM series

Reviews:

Related manuals for AKD PDMM series

Brands by name

Popular brands

Kollmorgen AKD PDMM series, User Manual

Search results

Summary of Contents for AKD PDMM series

Reviews:

Related manuals for AKD PDMM series

Brands by name

Popular brands