instructions for
torque adaptor digital 1/2”sq. drive
40-200Nm (29.5-147.5lb.ft)
model no:
stW290.v2
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. safety
WarNiNg!
do Not
use the digital torque adaptor if damaged or thought to be faulty.
9
ensure all workshop safety rules, regulations and conditions are complied with when using this digital torque adaptor.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
After use clean with a soft dry cloth and store in a safe, dry, childproof location.
9
Keep the digital torque adaptor away from magnets.
8
do Not
subject the digital torque adaptor to excessive force or shocks.
8
do Not
drop or throw the digital torque adaptor.
8
do Not
use digital torque adaptor unless you have been instructed in its use by a qualified person.
8
do Not
leave the digital torque adaptor in any place exposed to excessive heat, humidity or direct sunlight.
8
do Not
use organic solvents such as alcohol or thinners to clean the digital torque adaptor.
8
do Not
submerge the digital torque adapter in water or any other liquid.
8
do Not
disassemble the digital torque adaptor.
8
do Not
exceed the permitted torque value for the digital torque adaptor.
9
To ensure accurate measurement periodic re-calibration is necessary.
2. iNtroductioN
d
esigned for use with a ratchet or breaker bar. Ideal for work around the engine bay and the tightening of wheel nuts to factory specifications.
Large LCD display with selectable readings in Nm, lb.ft, lb.in, kg-cm or kg-m and accurate to ±2% of stated capacity. Memory stores up to
50 readings and features auto shut off after 70 seconds. Supplied with certificate and storage case.
3. specificatioN
model no: .................................................................
STW290
drive type: ..................................................................
1/2”Sq.
length: .........................................................................
75mm
range: ........................................
40-200Nm (29.5-147.5lb.ft)
Battery: .......................................................
2 x AAA supplied
4. operatioN
WarNiNg!
do Not
press Mem and On/off button
together as this will enter the unit into calibration mode.
4.1.
poWer oN
(fig.1).
4.1.1.
Attach the adaptor to a ratchet or breaker bar.
4.1.2.
After 2 seconds the LCD panel will show 0.0.
4.1.3.
tighten the nut or bolt.
4.1.4.
the lcd displays the torque value measured.
Note: If not used for 70 seconds the Digital Torque Adaptor will
automatically shut off.
4.2.
HoW to select uNit
(fig.1).
Press mem and Peak / trace button together and release to
select different torque units.
note: When you change units the target setting will also be
changed to the new units value.
this digital torque Adaptor contains 5 unit selections.
(kg-cm, kg-m, in-lb, ft-lb, N-m).
4.3.
HoW to select target torque value
(fig.1).
4.3.1.
Increase (+): Press and hold the (+) button to increase the
current target value.
s
TW290.V2 | Issue:1 31/01/18
Original Language Version
© Jack sealey limited
refer to
instruction
manual
Wear eye
protection
fig.1
