4.3.2.
Decrease (-): Press and hold the (-) button to lower the current target value.
4.3.3.
the target will show for 10 seconds.
4.3.4.
After 10 seconds the lcd will display 0.0.
Note: When the digital torque adaptor get to 20 units before the target, the red LED will flash and an intermittent buzzer will sound,
warning that the target value is close.
When the target value is attained the red LED will be illuminated and the buzzer will sound continuously.
4.4.
HOW TO SET PEAK OR TRACE (fig.1).
4.4.1.
peak:
Press and release Peak/Trace - button when the digital torque adaptor is on. The LCD panel shows PtoP.
4.4.1.1.
The LCD panel shows 0.0 after 2 seconds.
4.4.2.
trace:
Press and release Peak/Trace - button when the digital torque adaptor is on.
4.4.3.
the lcd panel shows trAce.
4.4.4.
The LCD panel shows 0.0 after 2 seconds.
4.5.
turN off
(fig.1).
4.5.1.
If the adaptor is not used for 70 seconds, it will automatically shut down.
4.5.2.
To manually turn off the digital torque adaptor press and release the On/Off button.
4.6.
memory
(fig.1).
4.6.1.
to display the stored readings. turn on the digital torque adaptor.
4.6.2.
Press and release the mem button.
4.6.3.
The display shows the memory number is P01 and then the Torque Value.
4.6.4.
Press and release the “M” button, again.
4.6.5.
The display shows the memory number is P02 and then the Torque Value.
note: this digital torque Adaptor stores the last 50 torque value readings, P01 is the latest reading, P50 is the oldest.
5. maiNteNaNce
5.1.
battery replacemeNt
(fig.2)
5.1.1.
remove the two screws from the battery cover.
5.1.2.
Lift off the battery cover.
5.1.3.
remove the battery from the holder.
5.1.4.
install new batteries observing correct polarity.
5.1.5.
Refit the battery cover and the screws.
note: When the battery is low the will light.
remove the battery if the torque adaptor is to be stored for a long time.
Battery life is dependant on battery quality and the amount of torque adaptor is used
(typical life is up to 55 hours).
5.2.
calibratioN
5.2.1.
Periodic calibration is required for this product contact your sealey stockist for details.
© Jack sealey limited
fig.2
Original Language Version
sealey group, Kempson Way, suffolk business park, bury st edmunds, suffolk. ip32 7ar
01284 757500
01284 703534
www.sealey.co.uk
Note
: it is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
important
: no liability is accepted for incorrect use of this product.
Warranty
: Guarantee is 12 months from purchase date, proof of which is required for any claim.
eNviroNmeNt protectioN
recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
battery removal see sectioN 5.1
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products
containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme. Jack
Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705.
s
TW290.V2 | Issue:1 31/01/18
Weee regulatioNs
dispose of this product at the end of its working life in compliance with the eu directive on Waste electrical and electronic equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
