manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

163

 

 

Register

 

SPI0

 

SPI2/I2S

 

SPI0_REMAP = 1 

PA15(SPI0_NSS) 

PB3(SPI0_SCK) 

PB4(SPI0_MISO) 

PB5(SPI0_MOSI) 

- 

SPI2_REMAP = 0 

- 

PA15(SPI2_NSS/I2S2_WS) 

PB3(SPI2_SCK/I2S2_CK) 

PB4(SPI2_MISO) 

PB5(SPI2_MOSI/I2S2_SD) 

SPI2_REMAP = 1 

- 

PA4(SPI2_NSS/I2S2_WS) 

PC10(SPI2_SCK/I2S2_CK) 

PC11(SPI2_MISO) 

PC12(SPI2_MOSI/I2S2_SD) 

7.4.9. 

CAN0/1 AF remapping 

The CAN0 signals can be mapped on Port A, Port B or Port D as shown in table below. For 
port D, remapping is not possible in devices delivered in 64-pin packages. 

Table 7-10. CAN0/1 alternate function remapping 

Register

 (1)

 

CAN0

 

CAN1

 

CAN0_REMAP[1:0] 

=“00” 

PA11(CAN0_RX) 

PA12(CAN0_TX) 

- 

CAN0_REMAPI[1:0] 

=“10” 

  PB8(CAN0_RX) 

PB9(CAN0_TX) 

- 

CAN0_REMAP[1:0] 

=“11”

(2)

 

PD0(CAN0_RX) 

PD1(CAN0_TX) 

- 

CAN1_REMAP 

= “0” 

- 

PB12(CAN1_RX) 

PB13(CAN1_TX) 

CAN1_REMAP 

= “1” 

- 

PB5(CAN1_RX) 

PB6(CAN1_TX) 

1. 

CAN0_RX and CAN0_TX in connectivity  line devices; CAN_RX and CAN_TX in other 

devices with a single CAN interface. 

2. 

Remap not available on 36-pin package. 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Particle B Series Quick Start Manual preview
B Series
Brand: Particle Pages: 6
Baccara G75-DFC Installation Operation & Maintenance preview
G75-DFC
Brand: Baccara Pages: 16
Harmonic Drive CHA Engineering Data preview
CHA
Brand: Harmonic Drive Pages: 85
OMC W150 Installation And Maintenance Instruction preview
W150
Brand: OMC Pages: 18
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Brand: SAI HVAC Pages: 16
Sailor N420 Technical Manual preview
N420
Brand: Sailor Pages: 1
YASKAWA U1000 iQpump Drive User Manual preview
U1000 iQpump Drive
Brand: YASKAWA Pages: 426
YASKAWA Motoman DX200 Safety Notes preview
Motoman DX200
Brand: YASKAWA Pages: 26
YASKAWA motoman NX100 Instructions Manual preview
motoman NX100
Brand: YASKAWA Pages: 210
YASKAWA Z1000 CIMR-ZU*A Series User Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 400
YASKAWA Z1000 CIMR-ZU*A Series Technical Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 466
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Brand: fadini Pages: 28
Zencontrol zc-controller Instructions preview
zc-controller
Brand: Zencontrol Pages: 2
Daikin KBRCS01A Quick Start Manual preview
KBRCS01A
Brand: Daikin Pages: 2
Advantech PCI-1760U Startup Manual preview
PCI-1760U
Brand: Advantech Pages: 3
Sparkfun Electronics Explorer Dongle Manual preview
Explorer Dongle
Brand: Sparkfun Electronics Pages: 16
A & H AMFLOW A2-ACM Installation, Operation & Service Manual preview
AMFLOW A2-ACM
Brand: A & H Pages: 35
MegaLite MEMO CORE CONTROL User Manual preview
MEMO CORE CONTROL
Brand: MegaLite Pages: 11

Brands by name

Popular brands

Load more brands