manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

134

 

 

0: Disabled ADC0 clock 

1: Enabled ADC0 clock 

8 

PGEN   

GPIO port G clock enable 

This bit is set and reset by software. 

0: Disabled GPIO port G clock 

1: Enabled GPIO port G clock 

7 

PFEN   

GPIO port F clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port F clock 

1: Enabled GPIO port F clock 

6 

PEEN   

GPIO port E clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port E clock 

1: Enabled GPIO port E clock 

5 

PDEN   

GPIO port D clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port D clock 

1: Enabled GPIO port D clock 

4 

PCEN   

GPIO port C clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port C clock 

1: Enabled GPIO port C clock 

3 

PBEN   

GPIO port B clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port B clock 

1: Enabled GPIO port B clock 

2 

PAEN   

GPIO port A clock enable   

This bit is set and reset by software. 

0: Disabled GPIO port A clock 

1: Enabled GPIO port A clock 

1 

Reserved 

Must be kept at reset value 

0 

AFEN 

Alternate function IO clock enable 

This bit is set and reset by software. 

0: Disabled Alternate Function IO clock 

1: Enabled Alternate Function IO clock 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

GE RSTi-EP User Manual preview
RSTi-EP
Brand: GE Pages: 425
C Prox Ltd FP1 User Manual preview
FP1
Brand: C Prox Ltd Pages: 5
Hans Grohe iBox Hub 25020180 Assembly Instruction And Instructions For Use preview
iBox Hub 25020180
Brand: Hans Grohe Pages: 36
YASKAWA PROFINET V1000 Technical Manual preview
PROFINET V1000
Brand: YASKAWA Pages: 49
M-system MSP10 Instruction Manual preview
MSP10
Brand: M-system Pages: 17
WINDY NATION CHC-LCD-30FM User Manual preview
CHC-LCD-30FM
Brand: WINDY NATION Pages: 16
Identiv Freedom Bridge FB3 Installation Manual preview
Freedom Bridge FB3
Brand: Identiv Pages: 2
Linear Technology LTC3703 Manual preview
LTC3703
Brand: Linear Technology Pages: 32
aerl CoolMax SRX Installation And Operation User Manual preview
CoolMax SRX
Brand: aerl Pages: 27
Current Mini LOOP BT Quick Start Manual preview
Mini LOOP BT
Brand: Current Pages: 4
PEAS VC-530E User Manual preview
VC-530E
Brand: PEAS Pages: 4
Sollae Systems CIE-M10A User Manual preview
CIE-M10A
Brand: Sollae Systems Pages: 72
Teradek CTRL.1 Quick Start Manual preview
CTRL.1
Brand: Teradek Pages: 10
ICP DAS USA CAN-8124 User Manual preview
CAN-8124
Brand: ICP DAS USA Pages: 153
3M Touch Screen Controller EX112 Reference Manual preview
Touch Screen Controller EX112
Brand: 3M Pages: 40
Niko 410-00121 Manual preview
410-00121
Brand: Niko Pages: 10
Omron EJ1N-TC2 Operation Manual preview
EJ1N-TC2
Brand: Omron Pages: 25
Monosem CS 3000-16 Manual preview
CS 3000-16
Brand: Monosem Pages: 68

Brands by name

Popular brands

Load more brands