manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

479

 

 

0: No bus error 

1: A bus error detected 

7 

TBE 

I2C_DATA is empty during transmitting 

This bit is set by hardware after it moves a byte from I2C_DATA to shift register and 

cleared by writing a byte to I2C_DATA. If both the shift register and I2C_DATA are 

empty, writing I2C_DATA won’t clear TBE (refer to Programming Model for detail). 

0: I2C_DATA is not empty 

1: I2C_DATA is empty, software can write 

6 

RBNE 

I2C_DATA is not empty during receiving 

This bit is set by hardware after it moves a byte from shift register to I2C_DATA 

and cleared by reading I2C_DATA. If both BTC and RBNE are asserted, reading 

I2C_DATA won’t clear RBNE because the shift register’s byte will be moved to 

I2C_DATA immediately. 

0: I2C_DATA is empty 

1: I2C_DATA is not empty, software can read 

5 

Reserved 

Must be kept at reset value. 

4 

STPDET 

STOP signal is detected in slave mode 

This  bit  is  set  by  hardware  and  cleared  by  reading  I2C_STAT0  and  then  writing 

I2C_CTL0. 

0: STOP signal not detected in slave mode 

1: STOP signal detected in slave mode 

3 

ADD10SEND 

Header of 10-bit address is sent in master mode 

This bit is set by hardware and cleared by reading I2C_STAT0 and writing 

I2C_DATA. 

0: No header of 10-bit address is sent in master mode 

1: Header of 10-bit address is sent in master mode 

2 

BTC 

Byte transmission is completed. 

If a byte is already received in shift register but I2C_DATA is still full in receiving 

mode or a byte is already sent out from shift register but I2C_DATA is still empty in 

transmitting mode, the BTC flag is asserted if SCL stretching enabled. 

This bit is set by hardware and cleared by 3 ways as follow: 

1. Software clearing: reading I2C_STAT0 followed by reading or writing I2C_DATA 

2. Hardware clearing: sending the STOP signal or START signal 

3. Bit 0 (I2CEN bit) of the I2C_CTL0 is reset. 

0: BTC not asserted 

1: BTC asserted 

1 

ADDSEND 

Address is sent and ACK is received in master mode or address is received and 

matches with its own address in slave mode. 

This  bit  is  set  by  hardware  and  cleared  by  reading  I2C_STAT0  and  reading 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

ZKTeco SC800 User Manual preview
SC800
Brand: ZKTeco Pages: 123
NEC 78K0S/KA1+ Preliminary User'S Manual preview
78K0S/KA1+
Brand: NEC Pages: 304
EasyIO FG Series User Manual preview
FG Series
Brand: EasyIO Pages: 12
RMG GSM 3ST User Manual preview
GSM 3ST
Brand: RMG Pages: 6
Canarm MC Series Installation Manual preview
MC Series
Brand: Canarm Pages: 3
Lawler 801 Installation & Maintenance Manual preview
801
Brand: Lawler Pages: 4
QTP 10900 Quick Start Manual preview
10900
Brand: QTP Pages: 2
National Instruments NI cRIO-9036 User Manual preview
NI cRIO-9036
Brand: National Instruments Pages: 40
National Instruments cRIO-9063 Manual preview
cRIO-9063
Brand: National Instruments Pages: 28
National Instruments NI PXI-8104 Installation Manual preview
NI PXI-8104
Brand: National Instruments Pages: 7
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Brand: RBI Pages: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Brand: RBH Access Technologies Pages: 36
S&C PMH Inspection Manual preview
PMH
Brand: S&C Pages: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Brand: S&C Pages: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Brand: S&C Pages: 19
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Brand: SAI HVAC Pages: 16
Sailor N420 Technical Manual preview
N420
Brand: Sailor Pages: 1
Vageo DT-1 Plus Manual preview
DT-1 Plus
Brand: Vageo Pages: 2

Brands by name

Popular brands

Load more brands