manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual, Page: 527 / 853

Share
Download
GigaDevice Semiconductor GD32F10 Series User Manual Download Page 527

                                                                                                             

GD32F10x User Manual

 

527

 

 

The interrupt logic generates interrupt when at least one of the selected status flags is high. 
An interrupt enable register is provided to allow the logic to generate a corresponding interrupt. 

The DMA interface provides a method for fast data transfers between the SDIO data FIFO 
and memory. The following example describes how to implement this method: 

1. Complete the card identification process 

2. Increase the SDIO_CLK frequency 

3. Send CMD7 to select the card and configure the bus width 

4. Configure the DMA1 as follows: 

Enable  DMA1  controller  and  clear  any  pending  interrupts.  Configure  the  DMA1_Channel3 
source  address  register  with  the  memory  base  address  and  DMA1_Channel3  destination 
address  register  with  the  SDIO_FIFO  register  address.  Program  DMA1_Channel3  control 
register (memory increment, not peripheral increment, peripheral and source width is word 
size, M2M disable). 

5. Write block to card as follows: 

Write  the  data  size  in  bytes  in  the  SDIO_DATALEN  register. Write  the  block  size  in  bytes 
(BLKSZ) in the SDIO_DATACTL register; the host sends data in blocks of size BLKSZ each. 
Program  SDIO_CMDAGMT  register  with  the  data  address,  where  data  should  be  written. 
Program the SDIO command control register (SDIO_CMDCTL): CMDIDX with 24, CMDRESP 
with  1  (SDIO  card  host  waits  for  a  short  response);  CSMEN  with  ‘1’  (enable  to  send  a 
command). Other fields are their reset value. 

When the CMDRECV flag is set, program the SDIO data control register (SDIO_DATACTL): 
DATAEN with 1 (enable to send data); DATADIR with 0 (from controller to card); TRANSMOD 
with  0  (block  data  transfer);  DMAEN  with  1  (DMA  enabled);  BLKSZ  with  0x9  (512  bytes). 
Other bits don’t care. 

Wait for DTBLKEND flag is set. Check that no channels are still enabled by polling the DMA 
Interrupt Flag register. 

It consists the following subunits: 

Register unit   

The  register  unit  which  contains  all  system  registers  generates  the  signals  to  control  the 
communication between the controller and card. 

Data FIFO   

The data FIFO unit has a data buffer, uses as transmit and receive FIFO. The FIFO contains 
a 32-bit wide, 32-word deep data buffer. The transmit FIFO is used when write data to card 
and TXRUN in SDIO_STAT register is 1. The data to be transferred is written to transmit FIFO 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments