manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual, Page: 706 / 853

Share
Download
GigaDevice Semiconductor GD32F10 Series User Manual Download Page 706

                                                                                                             

GD32F10x User Manual

 

706

 

 

Configure  AFIO_PCF0  to  define  which  interface  mode  is  selected  (MII  or  RMII). 

Configure GPIO module to make selected PADs to alternate function. 

 

Wait the resetting complete 

Polling  the  ENET_DMA_BCTL  register  until  the  SWR  bit  is  reset.  (SWR  bit  is  set  by 

default after power-on reset or system reset). 

 

Obtain and configure the parameters in PHY register 

According  to  the  frequency  of  HCLK,  configure  the  SMI  clock  frequency  and  access 

external PHY register to obtain the information of PHY (e.g. support Half/Full duplex or 

not,  support  10M/100Mbit  speed  or  not,  and  so  on).  Based  on  supported  mode  of 

external PHY, configure ENET_MAC_CFG register consistent with PHY register. 

 

Initialize the DMA in Ethernet module for transaction 

Configure  the  ENET_DMA_BCTL,  ENET_DMA_RDTADDR,  ENET_DMA_TDTADDR, 

ENET_DMA_CTL registers to initialize the DMA module. (Detailed information refer to 

DMA controller description

). 

 

Initialize the physical memory space for descriptor table and data buffer 

According to the address value in ENET_DMA_RDTADDR and ENET_DMA_TDTADDR 

register, program transmitting and receiving descriptors (with DAV=1) and data buffer. 

 

Enable MAC and DMA module to start transmit and receive 

Set TEN and REN bit in ENET_MAC_CFG register to make MAC work for transmit and 

receive. Set STE and SRE bit in ENET_DMA_CTL register to make DMA controller work 

for transmit and receive. 

 

If transmitting frames is needed 

1)  Choose one or more programmed transmitting descriptor, write the transmit frame 

data into buffer address which is decided in TDES. 

2)  Set the DAV bit in these one or more transmit frame descriptor. 

3)  Write any value in ENET_DMA_TPEN register to make TxDMA exit suspend state 

and start transmitting. 

4)  There are two methods for application to confirm whether current transmitting frame 

is complete or not. The first method is that application can poll the DAV bit of current 

transmit  descriptor  until  it  is  reset,  this  means  the  transmitting  is  complete.  The 

second method can be used only when INTC=1. Application can poll the TS bit in 

ENET_DMA_STAT register until it is set, this means the transmitting is complete. 

 

If receiving frames is enabled 

1)  Check the first receive descriptor in descriptor table (whose address is configured in 

ENET_DMA_RDTADDR register). 

2)  If DAV bit in RDES0 is reset, then the descriptor is used and receive buffer space 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments