manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

445

 

 

0: Transmit data buffer is not empty. 

1: Transmit data buffer is empty. 

6 

TC 

Transmission complete 

This bit is set after power on. If the TBE bit has been set, this bit is set when the 

transmission  of  current  data  is  complete.  An  interrupt  occurs  if  the  TCIE  bit  in 

USART_CTL0 is set. 

Software can clear this bit by writing 0 to it. 

0: Transmission of current data is not complete. 

1: Transmission of current data is complete. 

5 

RBNE 

Read data buffer not empty 

This bit is set when the read data buffer is filled with a data frame, which has been 

received through the receive shift register. An interrupt occurs if the RBNEIE bit in 

USART_CTL0 is set. 

Software can clear this bit by writing 0 to it or by reading the USART_DATA register. 

0: Read data buffer is empty. 

1: Read data buffer is not empty. 

4 

IDLEF 

IDLE frame detected flag 

This bit is set when the RX pin has been detected in idle state for a frame time. An 

interrupt occurs if the IDLEIE bit in USART_CTL0 is set. 

Software  can  clear  this  bit  by  reading  the  USART_STAT  and  USART_DATA 

registers one by one. 

0: The USART module does not detect an IDLE frame. 

1: The USART module has detected an IDLE frame. 

3 

ORERR 

Overrun error   

This bit is set if the RBNE is not cleared and a new data frame is received through 

the  receive shift  register.  An  interrupt  occurs  if  the  ERRIE bit  in  USART_CTL2  is 

set. 

Software  can  clear  this  bit  by  reading  the  USART_STAT  and  USART_DATA 

registers one by one. 

0: The USART does not detect a overrun error. 

1: The USART has detected a overrun error. 

2 

NERR 

Noise error flag 

This bit is set if the USART detects noise on the RX pin when receiving a frame. An 

interrupt occurs if the ERRIE bit in USART_CTL2 is set. 

Software  can  clear  this  bit  by  reading  the  USART_STAT  and  USART_DATA 

registers one by one. 

0: The USART does not detect a noise error. 

1: The USART has detected a noise error. 

1 

FERR 

Frame error flag 

This  bit  is  set  when  the  RX  pin  is  detected  low  during  the  stop  bits  of  a  receive 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Samson 3430 Operating Instructions Manual preview
3430
Brand: Samson Pages: 52
Samson 3275 Mounting And Operating Instructions preview
3275
Brand: Samson Pages: 32
Danfoss Cascade Operating Instructions Manual preview
Cascade
Brand: Danfoss Pages: 59
Ultratec SureFire Operation Manual preview
SureFire
Brand: Ultratec Pages: 33
+GF+ EA15 Instruction Manual preview
EA15
Brand: +GF+ Pages: 3
Bender CC613-H Series Manual preview
CC613-H Series
Brand: Bender Pages: 28
Quantum NE PLUS Basic Operation Instructions preview
NE PLUS
Brand: Quantum Pages: 20
4IPNET WHG301 Quick Installation Manual preview
WHG301
Brand: 4IPNET Pages: 11
LEGRAND Arteor 5 742 74 Quick Start Manual preview
Arteor 5 742 74
Brand: LEGRAND Pages: 2
Srne ML4860N15 User Manual preview
ML4860N15
Brand: Srne Pages: 13
Rauch quantron e Operator'S Manual preview
quantron e
Brand: Rauch Pages: 85
Texas Instruments CC2530-CC2592EM Quick Start Manual preview
CC2530-CC2592EM
Brand: Texas Instruments Pages: 3
OCL DLC-1.1 Quick Start Manual preview
DLC-1.1
Brand: OCL Pages: 2
ISC APECS Operational Instructions preview
APECS
Brand: ISC Pages: 20
Neousys Technology Nuvo-3000 Series User Manual preview
Nuvo-3000 Series
Brand: Neousys Technology Pages: 101
Hanna Instruments HI 9912 Instruction Manual preview
HI 9912
Brand: Hanna Instruments Pages: 28
Bard CompleteStat CS9B-THOA Quick Start Manual preview
CompleteStat CS9B-THOA
Brand: Bard Pages: 10
CASTLE THUNDERBIRD-36 User Manual preview
THUNDERBIRD-36
Brand: CASTLE Pages: 2

Brands by name

Popular brands

Load more brands