manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

642

 

 

This bit is reset by hardware when the mailbox 1 is empty. 

14:12 

Reserved 

Must be kept at reset value. 

11 

MTE1 

Mailbox 1 transmit error 

This bit is set by hardware when the transmit error occurs. This bit is reset by 

writting 1 to this bit or MTF1 bit in CAN_TSTAT register. This bit is reset by 

hardware when next transmit starts. 

10 

MAL1 

Mailbox 1 arbitration lost 

This bit is set when the arbitration lost occurs. This bit is reset by writting 1 to this 

bit or MTF1 bit in CAN_TSTAT register. This bit is reset by hardware when next 

transmit starts. 

9 

MTFNERR1 

Mailbox 1 transmit finished with no error 

This bit is set when the transmission finishes and no error occurs. This bit is reset 

by writting 1 to this bit or MTF1 bit in CAN_TSTAT register. This bit is reset by 

hardware when the transmission finishes with error. 

0: Mailbox 1 transmit finished with error 

1: Mailbox 1 transmit finished with no error 

8 

MTF1 

Mailbox 1 transmit finished 

This bit is set by hardware when the transmission finishes or aborts. This bit is 

reset by writting 1 to this bit or TEN bit in CAN_TMI1 is 1. 

0: Mailbox 1 transmit is progressing 

1: Mailbox 1 transmit finished 

7 

MST0 

Mailbox 0 stop transmitting 

This bit is set by the software to stop mailbox 0 transmitting. 

This bit is reset by the hardware when the mailbox 0 is empty. 

6:4 

Reserved 

Must be kept at reset value. 

3 

MTE0 

Mailbox 0 transmit error 

This bit is set by hardware when the transmit error occurs. This bit is reset by 

writting 1 to this bit or MTF0 bit in CAN_TSTAT register. This bit is reset by 

hardware when next transmit starts. 

2 

MAL0 

Mailbox 0 arbitration lost 

This bit is set when the arbitration lost occurs. This bit is reset by writting 1 to this 

bit or MTF0 bit in CAN_TSTAT register. This bit is reset by hardware when next 

transmit starts. 

1 

MTFNERR0 

Mailbox 0 transmit finished with no error 

This bit is set when the transmission finishes and no error occurs. This bit is reset 

by writting 1 to this bit or MTF0 bit in CAN_TSTAT register. This bit is reset by 

hardware when the transmission finishes with error. 

0: Mailbox 0 transmit finished with error 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

KELCO F60 Installation Instructions Manual preview
F60
Brand: KELCO Pages: 36
IFM CR710S Original Operating Instructions preview
CR710S
Brand: IFM Pages: 49
OES ISC-9000 Operational Instructions preview
ISC-9000
Brand: OES Pages: 3
Eaton C22- P Series Instruction Leaflet preview
C22- P Series
Brand: Eaton Pages: 2
S&C Micro-AT Quick Start Programming Manual preview
Micro-AT
Brand: S&C Pages: 12
Brooks GF100 Series Installation And Operation Manual preview
GF100 Series
Brand: Brooks Pages: 68
Infineon Technologies TC1796 User Manual preview
TC1796
Brand: Infineon Technologies Pages: 2150
Coremorrow Modular E70 Series User Manual preview
Modular E70 Series
Brand: Coremorrow Pages: 14
SMSC USB2250 Datasheet preview
USB2250
Brand: SMSC Pages: 35
VubIQ V60WGD03 User Manual preview
V60WGD03
Brand: VubIQ Pages: 17
CKD ABSODEX MINI AX6000M Series Manual preview
ABSODEX MINI AX6000M Series
Brand: CKD Pages: 24
Regin RDAS35-24C Mounting Instructions preview
RDAS35-24C
Brand: Regin Pages: 8
Infineon Cypress CY8CKIT-064S0S2-4343W Kit Manual preview
Cypress CY8CKIT-064S0S2-4343W
Brand: Infineon Pages: 52
NiGICO NRG AVR 1200 User Manual preview
NRG AVR 1200
Brand: NiGICO Pages: 9
Oriental motor EZ limo ESMC-A2 Operating Manual preview
EZ limo ESMC-A2
Brand: Oriental motor Pages: 94
Dahua Technology ASC1202B-S User Manual preview
ASC1202B-S
Brand: Dahua Technology Pages: 15
Cmsemicon BAT32G1 9 Series User Manual preview
BAT32G1 9 Series
Brand: Cmsemicon Pages: 1149
Tubbutec Sumtiple Construction Manual preview
Sumtiple
Brand: Tubbutec Pages: 5

Brands by name

Popular brands

Load more brands