manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

448

 

 

9 

PM 

Parity mode 

0: Even parity. 

1: Odd parity. 

8 

PERRIE 

Parity error interrupt enable 

If this bit is set, an interrupt occurs when the PERR bit in USART_STAT is set. 

0: Parity error interrupt is disabled. 

1: Parity error interrupt is enabled. 

7 

TBEIE 

Transmitter buffer empty interrupt enable 

If this bit is set, an interrupt occurs when the TBE bit in USART_STAT is set. 

0: Transmitter buffer empty interrupt is disabled. 

1: Transmitter buffer empty interrupt is enabled. 

6 

TCIE 

Transmission complete interrupt enable 

If this bit is set, an interrupt occurs when the TC bit in USART_STAT is set. 

0: Transmission complete interrupt is disabled. 

1: Transmission complete interrupt is enabled. 

5 

RBNEIE 

Read data buffer not empty interrupt and overrun error interrupt enable 

If  this  bit  is  set,  an  interrupt  occurs  when  the  RBNE  bit  or  the  ORERR  bit  in 

USART_STAT is set. 

0: Read data register not empty interrupt and overrun error interrupt disabled. 

1: Read data register not empty interrupt and overrun error interrupt enabled. 

4 

IDLEIE 

IDLE line detected interrupt enable 

If this bit is set, an interrupt occurs when the IDLEF bit in USART_STAT is set. 

0: IDLE line detected interrupt disabled. 

1: IDLE line detected interrupt enabled. 

3 

TEN 

Transmitter enable 

0: Transmitter is disabled. 

1: Transmitter is enabled. 

2 

REN 

Receiver enable 

0: Receiver is disabled. 

1: Receiver is enabled. 

1 

RWU 

Receiver wakeup from mute mode. 

Software can set this bit to make the USART work in mute mode and reset this bit 

to wake up the USART. 

In wake up by idle frame mode (WM=0), this bit can be reset by hardware when an 

idle frame has been detected. In wake up by address match mode (WM=1), this bit 

can  be  reset  by  hardware  when  receiving  an  address  match  frame  or  set  by 

hardware when receiving an address mismatch frame. 

0: Receiver in active mode. 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

ABATEC A1 Installation And Operation Instruction Manual preview
A1
Brand: ABATEC Pages: 8
Falcon RS500 Owner'S And Installer'S Manual preview
RS500
Brand: Falcon Pages: 3
Walchem W100 Troubleshooting Manual preview
W100
Brand: Walchem Pages: 10
Maximum Controls MAX ARM Installation And Owner'S Manual preview
MAX ARM
Brand: Maximum Controls Pages: 58
Toptech MultiLoad II EXL Installation Manual preview
MultiLoad II EXL
Brand: Toptech Pages: 83
Winbond W77E516 Manual preview
W77E516
Brand: Winbond Pages: 85
Swagelok TBVS4 User Manual preview
TBVS4
Brand: Swagelok Pages: 16
Qorvo QM33120WDK1 Quick Start Manual preview
QM33120WDK1
Brand: Qorvo Pages: 6
Planar Dome Md4/PCI Installation Manual preview
Dome Md4/PCI
Brand: Planar Pages: 162
THK TJU Instruction Manual preview
TJU
Brand: THK Pages: 134
OLYS MPPT5010 User Manual preview
MPPT5010
Brand: OLYS Pages: 4
Watersports Innovations The Boost Box WS 1107 Installation & Operation Instructions preview
The Boost Box WS 1107
Brand: Watersports Innovations Pages: 12
Parker IQAN-XS2 Instruction Book preview
IQAN-XS2
Brand: Parker Pages: 31
Z-Wave AC MASTER LITE Installation Manual preview
AC MASTER LITE
Brand: Z-Wave Pages: 27
TAC Xenta 102 Handbook preview
Xenta 102
Brand: TAC Pages: 76
Hamamatsu C7557 Instruction Manual preview
C7557
Brand: Hamamatsu Pages: 50
Harmonic Drive YukonDrive-1021 Operating Manual preview
YukonDrive-1021
Brand: Harmonic Drive Pages: 53
Instruments of Things IO-Lights User Manual preview
IO-Lights
Brand: Instruments of Things Pages: 12

Brands by name

Popular brands

Load more brands