manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

421

 

 

Single pulse mode 

Single pulse mode is opposite to the repetitive mode, which can be enabled by setting SPM 

in TIMERx_CTL0. When you set SPM, the counter will be clear and stop when the next update 

event. 

Once  the  timer  is  set  to  operate  in  the  single  pulse  mode,  it  is  necessary  to  set  the  timer 

enable  bit CEN in the TIMERx_CTL0 register to 1 to enable the counter, then the CEN bit 

keeps at a high state until the update event occurs or the CEN bit is written to 0 by software. 

If the CEN bit is cleared to 0 using software, the counter will be stopped and its value held. 

Timer debug mode 

When the Cortex

®

-M3 halted, and the TIMERx_HOLD configuration bit in DBG_CTL register 

set to 1, the TIMERx counter stops. 

 

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Hanbay RC Series Manual preview
RC Series
Brand: Hanbay Pages: 18
Danfoss ERC 211 User Manual preview
ERC 211
Brand: Danfoss Pages: 36
Olsberg OEC Instructions For Use Manual preview
OEC
Brand: Olsberg Pages: 68
SAI HVAC Compact Comfort VAV12 User Manual preview
Compact Comfort VAV12
Brand: SAI HVAC Pages: 16
Sailor N420 Technical Manual preview
N420
Brand: Sailor Pages: 1
KEB COMBIVERT F5 Safety Manual preview
COMBIVERT F5
Brand: KEB Pages: 16
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
IBC MVE2 Series Quick Start Manual preview
MVE2 Series
Brand: IBC Pages: 8
ACL ACL 5500 Installation Manual preview
ACL 5500
Brand: ACL Pages: 20
Epsolar eTracer ET4415BND Operation Manual preview
eTracer ET4415BND
Brand: Epsolar Pages: 44
Cardin Elettronica S486 Series Installation And Reference preview
S486 Series
Brand: Cardin Elettronica Pages: 56
Nice One-Max Installation And Use Instructions And Warnings preview
One-Max
Brand: Nice Pages: 32
Encelium Wired Manager - DALI Installation Instructions Manual preview
Wired Manager - DALI
Brand: Encelium Pages: 8
SUPMEA SUP-DC2000 User Manual preview
SUP-DC2000
Brand: SUPMEA Pages: 40
CDVI Ievo User Manual preview
Ievo
Brand: CDVI Pages: 24
Advanced Control Technologies th104 Installation Instructions preview
th104
Brand: Advanced Control Technologies Pages: 3
X10 SC503 Owner'S Manual preview
SC503
Brand: X10 Pages: 3
ECO POWER AL030W Installation Instructions preview
AL030W
Brand: ECO POWER Pages: 2

Brands by name

Popular brands

Load more brands