manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

693

 

 

This is valid only when the first segment (TDES0[28]) is set. 

0: The MAC automatic append a CRC to the end of the transmitted frame 

1: The MAC does not append a CRC to the end of the transmitted frame 

26 

DPAD 

Disable adding pad bit 

This is valid only when the first segment (TDES0[28]) is set. 

0: The DMA automatically adds padding byte and CRC to a frame shorter than 64 

bytes. Only the padding actually acts, the CRC is also appended. The DCRC bit is 

don’t care. 

1:The MAC does not automatically add padding to a frame   

25 

TTSEN 

Transmit timestamp function enable bit. 

This field is only valid when the First segment control bit (TDES0[28]) is set. 

0: Disable transmit timestamp function 

1: When TMSEN is set (ENET_PTP_TSCTL bit 0), IEEE 1588 hardware time 

stamping is activated for the transmit frame 

24 

Reserved 

Must be kept at reset value. 

23:22 

CM[1:0] 

Checksum mode bits 

0x0: Disabled checksum insertion function   

0x1: Only enable function for IP header checksum calculation and insertion 

0x2: Enable IP header checksum and payload checksum calculation and insertion, 

pseudo-header checksum is not calculated in hardware 

0x3: Enable IP Header checksum and payload checksum calculation and 

insertion, pseudo-header checksum is calculated in hardware. 

21 

TERM 

Transmit end for ring mode bit 

This bit is used only in ring mode and has higher priority than TCHM 

0: The current descriptor is not the last descriptor in the table 

1: The descriptor table reached its final descriptor. The DMA descriptor pointer 

returns to the start address of the table. 

20 

TCHM 

The second address chained mode bit 

This bit is used only in chain mode. When this bit, TCHM (TDES0[20]), is set, 

TB2S (TDES1[28:16]) is don’t care. 

0: The second address in the descriptor is the second buffer address 

1:The second address in the descriptor is the next descriptor address 

19:18 

Reserved 

Must be kept at reset value. 

17 

TTMSS 

Transmit timestamp status bit 

This bit is only valid when the descriptor’s last segment (LSG) control bit 

(TDES0[29]) is set. 

0: Timestamp was not captured 

1:A timestamp was captured for the described transmit frame and push into   

TDES2 and TDES3. 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Galcon 6100 Series Installation And Operating Instructions Manual preview
6100 Series
Brand: Galcon Pages: 32
Eaton S701 Instruction Leaflet preview
S701
Brand: Eaton Pages: 8
AAF MicroTech II UV05 Operation & Maintenance Manual preview
MicroTech II UV05
Brand: AAF Pages: 50
maxon motor EPOS2 24/5 Hardware Reference Manual preview
EPOS2 24/5
Brand: maxon motor Pages: 44
AUMA PROFOX PF-M100X Manual preview
PROFOX PF-M100X
Brand: AUMA Pages: 56
SUNWIND DR2210N -DDB User Manual preview
DR2210N -DDB
Brand: SUNWIND Pages: 53
Vasco 90.DR020000 Installation Manual preview
90.DR020000
Brand: Vasco Pages: 4
mikroElektronika mikromedia for dsPIC3 User Manual preview
mikromedia for dsPIC3
Brand: mikroElektronika Pages: 36
Suzhou MONARCH Control Technology Co., Ltd. NICE3000 New User Manual preview
NICE3000 New
Brand: Suzhou MONARCH Control Technology Co., Ltd. Pages: 233
Littlebits BUBBLE BOT Manual preview
BUBBLE BOT
Brand: Littlebits Pages: 22
Kuppersbusch EKEF 8752.0 Instructions For Use And Installation Instructions preview
EKEF 8752.0
Brand: Kuppersbusch Pages: 16
H3C WX2540H Installation Manual preview
WX2540H
Brand: H3C Pages: 40
Conrad 1460794 User Manual preview
1460794
Brand: Conrad Pages: 4
General Monitors 2602A Troubleshooting Manual preview
2602A
Brand: General Monitors Pages: 2
Sealey POWER PRODUCTS SA206 Instructions preview
POWER PRODUCTS SA206
Brand: Sealey Pages: 2
Sealey REG/MM.V2 Instructions preview
REG/MM.V2
Brand: Sealey Pages: 2
Sealey POWER PRODUCTS SA106 Instructions preview
POWER PRODUCTS SA106
Brand: Sealey Pages: 2
Sealey SA206 Instructions preview
SA206
Brand: Sealey Pages: 3

Brands by name

Popular brands

Load more brands