manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

676

 

 

suspending  a  certain  time  which  is  indicated  in  pause  time  field  of  detected  pause  control 

frame and then to transmit data. This function can set by RFCEN bit in ENET_MAC_FCTL 

register. If this function is not enabled, the MAC will ignore the received pause frames. If this 

function is enabled, MAC can decode this frame. Type field, opcode field and pause time field 

in the frame are all recognized by the MAC. During the pause time period, if MAC received a 

new  pause  frame,  the  new  pause  time  filed  value  is  loaded  to  the  pause  time  counter 

immediately.  If  the  new  pause  time  filed  is  zero,  then  the  pause  time  counter  stops  and 

transmit  operation  recovers.  Application  can  configure  PCFRM  bit  in  ENET_MAC_FRMF 

register to decide the solving method for such control frame. 

Receive checksum offload 

Receive checksum offload is enabled  when IPFCO  bit in ENET_MAC_CFG register is set. 

Receive  checksum  offload  can  calculate  the  IPv4  header  checksum  and  check  whether  it 

matches the contents of the IPv4 header checksum field. The MAC identifies IPv4  or IPv6 

frames by checking for the value of 0x0800 or 0x86DD respectively in the received Ethernet 

frame  type  field.  This  method  is  also  used  to  identify  frames  with  VLAN  tags.  Header 

checksum  error  bits  in  DMA  receive  descriptor  (the  7  bit  in  RDES0)  reflects  the  header 

checksum result. This bit is set if received IP header has the following errors: 

 

Any mismatch between the IPv4 calculation result by checksum offload module and the 
value in received frame’s checksum field. 

 

Any inconsistent between the data type of Ethernet type field and IP header version 

field. 

 

Received frame length is less than the length indicated in IPv4 header length field, or 

IPv4 or IPv6 header is less than 20 bytes. 

Receive checksum offload also identifies the data type of the IP packet is TCP, UDP or ICMP, 

and  calculate  their  checksum  according  to  TCP,  UDP  or  ICMP  specification.  Calculation 

process can include data of TCP/UDP/ICMPv6 pseudo-header. Payload checksum error bits 

in DMA receive descriptor (bit 0 in RDES0) reflects the payload checksum result. This bit is 

set if received IP payload has the following errors: 

 

Any mismatch between the TCP, UDP or ICMP checksum calculation result by 
checksum offload and the received TCP/UDP/ICMP frame’s checksum field. 

 

Any inconsistent between the received TCP, UDP or ICMP data length and length of IP 

header. 

The  received  checksum  offload  does  not  calculate  the  following  conditions:  Incomplete  IP 

packets, IP packets with security features, packets of IPv6 routing header and data type is 

not TCP, UDP or ICMP. 

Error handling 

 

If RxFIFO becomes full but the last received byte is not the end of frame (EOF), the 

RxFIFO will discard the whole frame data and return an overflow status. Also the 

counter of counting the overflow condition times will plus 1. 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
Samson 3372 User Manual preview
3372
Brand: Samson Pages: 8
Vacon 100X series Installation, Technical And Maintenance Manual preview
100X series
Brand: Vacon Pages: 132
Harmonic Drive RSF-B mini Series Manual preview
RSF-B mini Series
Brand: Harmonic Drive Pages: 32
WAGO 8003 Series Operating And Assembly Instructions preview
8003 Series
Brand: WAGO Pages: 2
SIATA PS0335 XP0/05 Service Manual preview
PS0335 XP0/05
Brand: SIATA Pages: 7
SLV 470700 Operating Manual preview
470700
Brand: SLV Pages: 11
Atmel Qmatrix Application Note preview
Qmatrix
Brand: Atmel Pages: 27
ZKTeco Notus Quick Start Manual preview
Notus
Brand: ZKTeco Pages: 13
Halma Alicat Scientific IVCD Operating Manual preview
Alicat Scientific IVCD
Brand: Halma Pages: 28
Calliope Calliope mini Starter Manual preview
Calliope mini
Brand: Calliope Pages: 38
Regin OPTIGO OP5 Manual preview
OPTIGO OP5
Brand: Regin Pages: 24
WAVESTREAM RMC-RRS011-HE01 Operation Manual preview
RMC-RRS011-HE01
Brand: WAVESTREAM Pages: 54
BioSmart PV-WM-MFR Operation Manual preview
PV-WM-MFR
Brand: BioSmart Pages: 24
Roger PR821-CH User Manual preview
PR821-CH
Brand: Roger Pages: 29
Jandy TruDose Installation And Operation Manual preview
TruDose
Brand: Jandy Pages: 78
Digital Equipment HSZ40 Reference Manual preview
HSZ40
Brand: Digital Equipment Pages: 118
Xantrex SOLAR CHARGE CONTROLLER 30 Owner'S Manual preview
SOLAR CHARGE CONTROLLER 30
Brand: Xantrex Pages: 40

Brands by name

Popular brands

Load more brands