GigaDevice Semiconductor GD32F10 Series Page 710 User Manual Download

Page: 710 / 853

GD32F10x User Manual

710

0x6: 48 bit times(For Half-duplex, must be reserved)

0x7: 40 bit times(For Half-duplex, must be reserved)

CSD

Carrier sense disable bit

0: The MAC transmitter generates carrier sense error and aborts the transmission

1: The MAC transmitter ignores the MII CRS signal during frame transmission in

Half-duplex mode. Loss of carrier error and no carrier error will not be generated.

Reserved

Must be kept at reset value.

SPD

Fast Ethernet speed bit

Indicates the speed in Fast Ethernet mode:

0: 10 Mbit/s

1: 100 Mbit/s

ROD

Receive own disable bit

This bit is not applicable if the MAC is operating in Full-duplex mode

0: The MAC receives all packets that are given by the PHY while transmitting

1: The MAC disables the reception of frames in Half-duplex mode

LBM

Loopback mode bit

0: The MAC operates in normal mode

1: The MAC operates in loopback mode at the MII.

DPM

Duplex mode bit

0: Half-duplex mode enable

1: Full-duplex mode enable

IPFCO

IP frame checksum offload bit

0: The checksum offload function in the receiver is disabled

1: IP frame checksum offload function enabled for received IP frame

RTD

Retry disable bit

This bit is applicable only in the Half-duplex mode

0: The MAC attempts retries up to 16 times based on the settings of BOL

1: The MAC attempts only 1 transmission.

Reserved

Must be kept at reset value.

APCD

Automatic pad/CRC drop bit

This bit only valid for a non tagged frame and its length field value is equal or less

than 1536.

0: The MAC forwards all received frames without modify it

1: The MAC strips the Pad/FCS field on received frames

6:5

BOL[1:0]

Back-off limit bits

When a collision occurred, the MAC needs to retry sending current frame after

delay some time. The base time unit for this delay time (dt) called slot time which

means 1 slot time is equal to 512 bit times. This delay time (dt) is a random integer

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for GD32F10 Series

Reviews:

Related manuals for GD32F10 Series

Brands by name

Popular brands

GigaDevice Semiconductor GD32F10 Series, User Manual

Search results

Summary of Contents for GD32F10 Series

Reviews:

Related manuals for GD32F10 Series

Brands by name

Popular brands