manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

434

 

 

register is set, or if the RBNEIE is set. 

If a noise error (NERR), parity error (PERR), frame error (FERR) or overrun error (ORERR) 
is generated during a receiving process, then NERR, PERR, FERR or ORERR will be set at 
same time with RBNE. If DMA is disabled, the software needs to check whether the RBNE 
interrupt is caused by noise error, parity error, framing error or overflow error when the RBNE 
interrupt occurs. 

16.3.5. 

Use DMA for data buffer access 

To  reduce  the  burden  of  the  processor,  DMA  can  be  used  to  access  the  transmitting  and 
receiving data buffer. The DENT bit in USART_CTL2 is used to enable the DMA transmission, 
and the DENR bit in USART_CTL2 is used to enable the DMA reception. 

When DMA is used for USART transmission, DMA transfers data from internal SRAM to the 
transmit  data  buffer  of  the  USART.  The  configuration  step  is  shown  in 

Figure  16-5. 

Configuration step when using DMA for USART transmission

.

 

Figure 16-5. Configuration step when using DMA for USART transmission 

Set the address of USART_DATA as 

the DMA destination address

Set the address of data in internal 

sram as the DMA source address

Set the number of data as the DMA 

transfer number

Set other configurations of DMA, 

interrupt enable, priority, etc

Clear the TC bit in USART_STAT 

Enable the DMA channel for USART

Wait the TC bit to be set

 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Wasp B2000 Installation Manual preview
B2000
Brand: Wasp Pages: 16
IBM 3708 End-User Reference preview
3708
Brand: IBM Pages: 144
OEG KMS Manual preview
KMS
Brand: OEG Pages: 168
Galcon 61 Series Installation And Operating Instructions Manual preview
61 Series
Brand: Galcon Pages: 35
Gardner Denver AirSmart G2 Installation Manual preview
AirSmart G2
Brand: Gardner Denver Pages: 22
Parker CHELSEA Owner'S Manual preview
CHELSEA
Brand: Parker Pages: 32
Rayrun NT30 Quick Start Manual preview
NT30
Brand: Rayrun Pages: 4
Netafim AlphaDisc BLE Quick Manual preview
AlphaDisc BLE
Brand: Netafim Pages: 4
TREND IQ422 Installation Instructions Manual preview
IQ422
Brand: TREND Pages: 12
Procom DGC-6D Operating Instructions Manual preview
DGC-6D
Brand: Procom Pages: 10
EpiSensor ZDR-10 User Manual preview
ZDR-10
Brand: EpiSensor Pages: 37
AC Tech SCF SERIES Quick Reference Manual preview
SCF SERIES
Brand: AC Tech Pages: 2
V-TAC VT-2472 Manual preview
VT-2472
Brand: V-TAC Pages: 2
Danfoss VLT MCD 201 Installation Manual preview
VLT MCD 201
Brand: Danfoss Pages: 36
Samson TROVIS 5579 Mounting And Operating Instructions preview
TROVIS 5579
Brand: Samson Pages: 182
Velleman-Kit EDU01 Manual preview
EDU01
Brand: Velleman-Kit Pages: 32
TDSi DIGIgarde PLUS User Manual preview
DIGIgarde PLUS
Brand: TDSi Pages: 71
Azbil AUR455 User Manual preview
AUR455
Brand: Azbil Pages: 68

Brands by name

Popular brands

Load more brands