manualshive.com logo in svg

GigaDevice Semiconductor GD32F10 Series, User Manual

The GigaDevice Semiconductor GD32F10 Series is a cutting-edge product that offers exceptional performance and versatility. To make the most of this innovative device, it is essential to have the User Manual. You can easily download the comprehensive manual for free from manualshive.com, ensuring you unlock its full potential.

Share
Download
background image

                                                                                                             

GD32F10x User Manual

 

542

 

 

R2 (CID, CSD register) 

Code  length  is  136  bits.  The  contents  of  the  CID  register  are  sent  as  a  response  to  the 
commands CMD2 and CMD10. The contents of the CSD register are sent as a response to 
CMD9. Only the bits [127..1] of the CID and CSD are transferred, the reserved bit [0] of these 
registers is replaced by the end bit of the response. 

Table 19-15. Response R2 

Bit position 

135 

134 

[133:128] 

[127:1] 

0 

Width 

1 

1 

6 

127 

1 

Value 

‘0’ 

‘0’ 

‘111111’ 

x 

‘1’ 

description 

start bit 

transmission bit 

reserved 

CID or CSD 

register and 

internal CRC7 

end bit 

R3 (OCR register) 

Code length is 48 bits. The contents of the OCR register are sent as a response to ACMD41 
(SD memory), CMD1 (MMC). The response of different cards may have a little different. 

Table 19-16. Response R3 

Bit position 

47 

46 

[45:40] 

[39:8] 

[7:1] 

0 

Width 

1 

1 

6 

32 

7 

1 

Value 

‘0’ 

‘0’ 

‘111111’ 

x 

‘1111111’ 

‘1’ 

description 

start bit 

transmission bit 

reserved 

OCR 

register 

reserved 

end bit 

R4 (Fast I/O) 

For MMC only. Code length 48 is bits. The argument field contains the RCA of the addressed 
card, the register address to be read out or written to, and its contents. The status bit in the 
argument is set if the operation was successful. 

Table 19-17. Response R4 for MMC 

Bit position 

47 

46 

[45:40] 

[39:8] Argument field 

[7:1] 

0 

Width 

1 

1 

6 

16 

1 

7 

8 

7 

1 

Value 

‘0’ 

‘0’ 

‘100111’ 

x 

x 

x 

x 

x 

‘1’ 

description 

start 

bit 

transmission 

bit 

CMD39 

RCA 

[31:16] 

status 

[15] 

register 

address 

[14:8] 

read 

register 

contents 

[7:0] 

CRC7 

end 

bit 

R4b 

For SD I/O only. Code length is 48 bits. The SDIO card receive the CMD5 will respond with a 
unique SD I/O response R4. 

Summary of Contents for GD32F10 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for GD32F10 Series

Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78
Danfoss AME 335 Installation Manual preview
AME 335
Brand: Danfoss Pages: 20
Danfoss CCR2 Installation Manual preview
CCR2
Brand: Danfoss Pages: 64
Samson 3277 Quick Manual preview
3277
Brand: Samson Pages: 2
Koer C35CBMS Manual preview
C35CBMS
Brand: Koer Pages: 6
Partizan PAB-FC2 Quick Start Manual preview
PAB-FC2
Brand: Partizan Pages: 7
Acard PCI-to-IDE ATA-133 User Manual preview
PCI-to-IDE ATA-133
Brand: Acard Pages: 33
S&C Micro-AT Quick Start Programming Manual preview
Micro-AT
Brand: S&C Pages: 12
Samson 46-5 Mounting And Operating Instructions preview
46-5
Brand: Samson Pages: 24
YOKOGAWA UT32A-C Operation Manual preview
UT32A-C
Brand: YOKOGAWA Pages: 10
CLS LDV-45 Manual preview
LDV-45
Brand: CLS Pages: 6
National Instruments NI cRIO-9036 Getting Started Manual preview
NI cRIO-9036
Brand: National Instruments Pages: 18

Brands by name

Popular brands

Load more brands