NEC ?PD703302 User Manual Download

Page: 139 / 709

CHAPTER 6 16-BIT TIMER/EVENT COUNTER P (TMP)

User’s Manual U16896EJ2V0UD

139

6.4 Registers

(1) TMP0 control register 0 (TP0CTL0)

The TP0CTL0 register is an 8-bit register that controls the operation of TMP0.

This register can be read or written in 8-bit or 1-bit units.

Reset sets this register to 00H.

The same value can always be written to the TP0CTL0 register by software.

TP0CE

TMP0 operation disabled (TMP0 reset asynchronously

Note

TMP0 operation enabled. TMP0 operation started.

TP0CE

TMP0 operation control

TP0CTL0

TP0CKS2 TP0CKS1 TP0CKS0

After reset: 00H R/W Address: FFFFF5A0H

<7>

/16

/32

/64

/128

TP0CKS2

Internal count clock selection

TP0CKS1

TP0CKS0

Note

TP0OPT0.TP0OVF bit, 16-bit counter, timer output (TOP00, TOP01 pins)

Cautions 1. Set the TP0CKS2 to TP0CKS0 bits when the TP0CE bit = 0.

When the value of the TP0CE bit is changed from 0 to 1, the

TP0CKS2 to TP0CKS0 bits can be set simultaneously.

2. Be sure to clear bits 3 to 6 to “0”.

Remark

: Main clock frequency

Summary of Contents for ?PD703302






































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ?PD703302

Reviews:

Related manuals for ?PD703302

Brands by name

Popular brands

NEC ?PD703302, User Manual

Search results

Summary of Contents for ?PD703302

Reviews:

Related manuals for ?PD703302

Brands by name

Popular brands