NEC ?PD703302 User Manual Download Page 334

Page: 334 / 709

CHAPTER 9 8-BIT TIMER H

User’s Manual U16896EJ2V0UD

334

Figure 9-8. Carrier Generator Mode (2/3)

Operation when CMPn0 register = N, CMPn1 register = M is set

CMPn0

CMPn1

TMHEn

INTTMHn

Carrier clock

TM5n count value

00H

00H 01H

00H

00H 01H

00H

TCE5n

TOHn

INTTM5n

NRZBn

NRZn

Carrier clock

00H 01H

M 00H 01H

00H 01H

INTTM5Hn

NRZBn

<1> <2>

<3>

<4>

<5>

<6>

<7>

8-bit timer 5n count clock

8-bit timer Hn count clock

8-bit timer counter

Hn count value

<1> When the TMHEn bit = 0 and the TCE5n bit = 0, the operation of 8-bit timer Hn is stopped.

<2> When the TMHEn bit is set to 1, 8-bit timer Hn starts counting. The carrier clock remains the default level at

this time.

<3> When the count value of 8-bit timer counter Hn and the set value of the CMPn0 register match, the first

INTTMHn signal is generated, the carrier clock signal is inverted, and the register that is compared with 8-bit

timer counter Hn changes from the CMPn0 register to the CMPn1 register. 8-bit timer counter Hn is cleared

to 00H.

<4> When the count value of 8-bit timer counter Hn and the set value of the CMPn1 register match, the INTTMHn

signal is generated, the carrier clock signal is inverted, and the register that is compared with 8-bit timer

counter Hn changes from the CMPn1 register to the CMPn0 register. 8-bit timer counter Hn is cleared to 00H.

A carrier clock with a fixed duty (other than 50%) is generated through the repetition of steps <3> and <4>.

<5> The INTTM5n signal is synchronized with 8-bit timer Hn and output as the INTTM5Hn signal.

<6> The carrier is output from the rising edge of the first carrier clock by setting the NRZn bit to 1.

<7> By clearing the NRZn bit to 0, the TOHn output is also maintained high level while the carrier clock is high

level, and does not change to low level (the high level width of the carrier waveform is guaranteed through

steps <6> and <7>).

Remark

n = 0, 1

<R>

Summary of Contents for ?PD703302






































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ?PD703302

Reviews:

Brands by name

Popular brands

NEC ?PD703302, User Manual

Search results

Summary of Contents for ?PD703302

Reviews:

Brands by name

Popular brands