NEC ?PD703302 User Manual Download

Page: 579 / 709

CHAPTER 19 STANDBY FUNCTION

User’s Manual U16896EJ2V0UD

579

Table 19-3. Operation Status in HALT Mode

When CPU Is Operating with Main Clock

Setting of HALT Mode

Item

When Subclock Is Not Used

When Subclock Is Used

CPU Stops

operation

ROM correction

Stops operation

Main clock oscillator

Oscillation enabled

Subclock oscillator

−

Oscillation enabled

Internal oscillator (f

) Operable

Interrupt controller

Operable

16-bit timer (TMP0)

Operable

16-bit timer (TM01)

Operable

8-bit timers (TM50, TM51)

Operable

Timer H (TMH0, TMH1)

Operable

Watch timer

Operable when main clock is selected as

count clock

Operable

Watchdog timer 1

Operable

Watchdog timer 2

Operable when f

/8 is selected as count

clock

Operable

CSI00, CSI01

Operable

Note

Operable

Serial interface

UART0, UART1

Operable

Key interrupt function

Operable

A/D converter

Operable

Real-time output

Operable

Clock monitor (CLM)

Operable

Power-on-clear (POC)

Operable

Low-voltage detection (LVI)

Operable

Port function

Retains status before HALT mode was set.

Internal data

The CPU registers, statuses, data, and all other internal data such as the contents of the

internal RAM are retained as they were before the HALT mode was set.

Note

Only in the

PD703302Y, 70F3302Y

Summary of Contents for ?PD703302






































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ?PD703302

Reviews:

Related manuals for ?PD703302

Brands by name

Popular brands

NEC ?PD703302, User Manual

Search results

Summary of Contents for ?PD703302

Reviews:

Related manuals for ?PD703302

Brands by name

Popular brands