manualshive.com logo in svg

NEC ?PD703302, User Manual

The NEC ?PD703302 is a versatile and reliable product that comes with a comprehensive User Manual, providing you with all the necessary information to utilize its features efficiently. You can download the manual for free from manualshive.com, ensuring a hassle-free experience while exploring the full potential of this incredible device.

Share
Download
background image

CHAPTER  19   STANDBY  FUNCTION 

User’s Manual  U16896EJ2V0UD 

578 

19.3  HALT Mode 

 

19.3.1  Setting and operation status 

The HALT mode is set when a dedicated instruction (HALT) is executed in the normal operation mode. 

In the HALT mode, the clock oscillator continues operating.  Only clock supply to the CPU is stopped; clock supply 

to the other on-chip peripheral functions continues. 

As a result, program execution is stopped, and the internal RAM retains the contents before the HALT mode was 

set.  The on-chip peripheral functions that are independent of instruction processing by the CPU continue operating. 

Table 19-3 shows the operation status in the HALT mode. 

The average power consumption of the system can be reduced by using the HALT mode in combination with the 

normal operation mode for intermittent operation. 

 

Cautions  1.  Insert five or more NOP instructions after the HALT instruction. 

 

2.  If the HALT instruction is executed with an unmasked interrupt request signal held pending, 

the system shifts to the HALT mode, but the HALT mode is immediately released by the 

pending interrupt request signal. 

 

19.3.2  Releasing HALT mode 

The HALT mode is released by a non-maskable interrupt request signal (NMI pin input, INTWDT1, INTWDT2 

signal), an unmasked maskable interrupt request signal, and reset signal (RESET pin input, WDTRES1, WDTRES2, 

POCRES, LVIRES, CLMRES signal). 

After the HALT mode has been released, the normal operation mode is restored. 

 

(1)  Releasing HALT mode by non-maskable interrupt request signal or unmasked maskable interrupt 

request signal 

The HALT mode is released by a non-maskable interrupt request signal or an unmasked maskable interrupt 

request signal, regardless of the priority of the interrupt request.  If the HALT mode is set in an interrupt 

servicing routine, however, an interrupt request that is issued later is serviced as follows. 

 

(a)  If an interrupt request signal with a priority lower than that of the interrupt request currently being serviced 

is issued, only the HALT mode is released, and that interrupt request signal is not acknowledged.  The 

interrupt request signal itself is retained. 

 

(b)  If an interrupt request signal with a priority higher than that of the interrupt request currently being 

serviced is issued (including a non-maskable interrupt request signal), the HALT mode is released and 

that interrupt request signal is acknowledged. 

 

Table 19-2.  Operation After Releasing HALT Mode by Interrupt Request Signal 

Release Source 

Interrupt Enabled (EI) Status 

Interrupt Disabled (DI) Status 

Non-maskable interrupt request signal 

Execution branches to the handler address 

Maskable interrupt request signal 

Execution branches to the handler 

address or the next instruction is 

executed 

The next instruction is executed 

 

(2)  Releasing HALT mode by reset 

The same operation as the normal reset operation is performed. 

 

Summary of Contents for ?PD703302






































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ?PD703302

Ubisys J1 Manual preview
J1
Brand: Ubisys Pages: 2
C Prox Ltd FP1 User Manual preview
FP1
Brand: C Prox Ltd Pages: 5
Faulhaber MC 5004 Technical Manual preview
MC 5004
Brand: Faulhaber Pages: 66
National Instruments cRIO-9064 User Manual preview
cRIO-9064
Brand: National Instruments Pages: 26
Encelium Wired Manager - DALI Installation Instructions Manual preview
Wired Manager - DALI
Brand: Encelium Pages: 8
Blucave CC-18LI-1 Original Instructions preview
CC-18LI-1
Brand: Blucave Pages: 2
Estyma iGNEO COMPACT User Manual preview
iGNEO COMPACT
Brand: Estyma Pages: 56
Sunlight Supply TITAN Controls Saturn 4 Instruction Manual preview
TITAN Controls Saturn 4
Brand: Sunlight Supply Pages: 4
VistaLab 2100-0003 Operating Manual preview
2100-0003
Brand: VistaLab Pages: 20
Belimo LMC230 Manual preview
LMC230
Brand: Belimo Pages: 10
VisAccess VXS-5 Installation Instructions preview
VXS-5
Brand: VisAccess Pages: 3
NXP Semiconductors Freescale FRDM-KL43Z User Manual preview
Freescale FRDM-KL43Z
Brand: NXP Semiconductors Pages: 15
Aeotec GEN5 Instructions preview
GEN5
Brand: Aeotec Pages: 2
Leroy-Somer R220 VSG+CCM Installation And Maintenance Manual preview
R220 VSG+CCM
Brand: Leroy-Somer Pages: 8
Clare Controls CH-OS-L Installation Sheet preview
CH-OS-L
Brand: Clare Controls Pages: 5
TELECO AUTOMATION TVRGBDU868ST24 Mounting preview
TVRGBDU868ST24
Brand: TELECO AUTOMATION Pages: 12
IEI Technology TANK-870-Q170-QGW Quick Installation Manual preview
TANK-870-Q170-QGW
Brand: IEI Technology Pages: 4
Nvidia Tegra Ventana Hardware Setup And Android Gingerbread Install Manual preview
Tegra Ventana
Brand: Nvidia Pages: 17

Brands by name

Popular brands

Load more brands