manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 884

12B

-

44

TURBOCHARGING

Turbocharger oil pipe: Removal - Refitting

K9K, and 780

12B

II - OPERATION FOR REMOVAL OF PART 
CONCERNED

a

Remove the turbocharger oil supply pipe hollow bolt
(

5

) .

a

Loosen the turbocharger oil supply pipe nut (

6

) on

the cylinder head.

a

Remove the turbocharger oil supply pipe nut (

6

) on

the cylinder head.

a

Remove the turbocharger oil supply pipe.

a

Wipe away any oil run-off.

REFITTING THE TURBOCHARGER OIL 
SUPPLY PIPE

I - REFITTING PREPARATION OPERATION

a

parts  always  to  be  replaced:  turbocharger  oil
supply pipe (10,09,03,01)

a

parts  always  to  be  replaced:  Turbocharger  oil
supply pipe bolt (10,09,03,04)

II - REFITTING OPERATION FOR PART 
CONCERNED

a

Fit a new turbocharger oil supply pipe.

a

Fit the turbocharger oil supply pipe nut on the cylin-
der head, without tightening it.

a

Refit a new hollow bolt on the turbocharger oil sup-
ply pipe.

a

Torque tighten:

- the

 turbocharger oil supply pipe nut on the cyl-

inder head (35 N.m)

 using the tool

 (Mot. 1566) 

or

the tool

 (Mot. 1746)

,

- the

 turbocharger oil supply pipe hollow bolt (14

N.m)

.

III - FINAL OPERATION

a

Fit the air filter unit air outlet pipe.

a

Tighten the clips on the air outlet pipe of the air filter
unit.

a

Clip the electric wiring onto the air filter unit air outlet
pipe.

a

Connect:

- the  turbocharging  regulation  solenoid  valve  con-

nector,

- the air flowmeter connector.

a

Refit  the  exhaust  gas  recirculation  solenoid  valve
(see 

14A

, 

Antipollution

, 

Exhaust  gas  recircula-

tion  solenoid  valve:  Removal  -  Refitting

,  page

14A-11

) .

a

Connect the battery (see 

Battery: Removal - Refit-

ting

) (80A, Battery).

a

Disconnect the high pressure pump flow and pres-
sure regulator connectors to prevent the engine from
starting.

a

Run the starter motor until the oil warning light goes
out (do this for a few seconds).

a

Switch off the ignition.

a

Connect the high pressure pump flow and pressure
regulator connectors.

a

Start the engine.

a

Let the engine idle then depress the accelerator sev-
eral times with no load.

a

Switch off the ignition.

a

Check:

- that the turbocharger is operating correctly,

- that there are no oil leaks from the turbocharger.

a

Connect  the

  Diagnostic  tool 

and  deal  with  any

present fault(s).

123811

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands