Renault Laguna III Manual Download Page 1511

Page: 1511 / 3699

19A

123

COOLING

Engine cooling fan assembly: Removal - Refitting

F4R

19A

REMOVAL

I - REMOVAL PREPARATION OPERATION

Position the vehicle on a two-post lift (see

Vehicle:

Towing and lifting

) (MR 415, 02A, Lifting equip-

ment).

Disconnect the battery (see

Battery: Removal - Re-

fitting

) (MR 415, 80A, Battery).

Remove:

- the engine cover,

- the engine undertray bolts,

- the engine undertray,

- the front bumper (see

Front bumper: Removal -

Refitting

) (MR 416, 55A, Exterior protection),

- the upper radiator cover,

- the headlights (see

Headlight: Removal - Refit-

ting

) (MR 415, 80B, Headlights),

- the front end panel (see

Front end panel: Remov-

al - Refitting

) (MR 416, 42A, Upper front struc-

ture).

Drain:

- the cooling system (see

19A

Cooling

system: Draining - Refilling

, page

19A-16

) ,

- the refrigerant circuit (see

Refrigerant circuit:

Draining - Filling

) (MR 415, 62A, Air conditioning).

Remove the cooling radiator (see

19A

Cooling

Cooling radiator: Removal - Refitting

, page

19A-

) .

II - REMOVAL OPERATION FOR PART
CONCERNED

Unclip the engine cooling fan assembly at (

) .

Remove:

- the engine cooling fan assembly from the cooling

radiator following the direction of the arrow,

- the bolts (

) from the « fan - motor » assembly,

- the « fan - motor » assembly from the engine cool-

ing fan assembly base.

REFITTING

I - REFITTING OPERATION FOR PART
CONCERNED

Refit:

- the « fan - motor » assembly to the engine cooling

fan assembly base.

- the bolts of the « fan - motor » assembly.

Tighten the bolts of the « fan - motor » assembly.

Refit the engine cooling fan assembly to the cooling
radiator.

Clip the fan unit onto the cooling radiator.

II - FINAL OPERATION.

Refit the cooling radiator (see

19A

Cooling

Cool-

ing radiator: Removal - Refitting

, page

19A-28

) .

IMPORTANT

When working in the engine compartment, take
care as the radiator fan(s) may start up unexpect-
edly (risk of being cut).

To avoid any risk of serious burns when the engine
is hot:

- do not open the expansion bottle cap,

- do not drain the cooling system,

- do not open the bleed screw(s).

123744

«
...
1509
1510
1511
1512
1513
...
»

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands

Renault Laguna III, Manual

Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands