manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 419

11A

-

41

TOP AND FRONT OF ENGINE

Crankshaft accessories pulley: Removal - Refitting

K4M

11A

a

The  camshaft  grooves  (

8

)  must  be  horizontal  and

offset downwards.

a

Remove the TDC setting pin

 (Mot. 1489)

.

a

Lock the flywheel using a screwdriver.

II - OPERATION FOR REMOVAL OF PART 
CONCERNED

a

Remove:

- the crankshaft accessories pulley bolt (

9

) ,

- the crankshaft accessories pulley.

REFITTING

I - REFITTING PREPARATION OPERATION

a

parts always to be replaced: Crankshaft acces-
sories pulley bolts (10,03,03,10)

parts always to be replaced: Crankshaft acces-
sories pulley (10,03,03,07)

a

Fit:

- the timing tool

 (Mot. 1496) 

 (

10

) fitted with the

 (Mot.

1750)

 (

11

) ,

- a lifting eye bolt (

12

) to secure the timing tool

 (Mot.

1496) 

fitted with the

 (Mot. 1750)

.

14490

14487

108873

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands