Renault Laguna III Manual Download Page 1338

Page: 1338 / 3699

17A

IGNITION

Plugs: Removal - Refitting

V4Y

17A

REMOVAL

I - REMOVAL PREPARATION OPERATION

Remove:

- the engine cover,

- the inlet manifold (see

12A

Fuel mixture

Inlet

distributor: Removal - Refitting

, page

12A-75

) ,

- the rear and front row ignition coils (see

17A

Igni-

tion

Coils: Removal - Refitting

, page

17A-1

) ,

- the windscreen wiper arms (see

Windscreen wip-

er arm: Removal - Refitting

) (85A, Wiping -

Washing),

- the scuttle panel grille (see

Scuttle panel grille:

Removal - Refitting

) (56A, Exterior equipment),

- the bolts from the wiper motor guard,

- the wiper motor guard,

- the scoop under the scuttle panel grille (see

Scoop

under the scuttle panel grille: Removal - Refit-
ting

) (56A, Exterior equipment).

II - OPERATION FOR REMOVAL OF PART
CONCERNED

Remove the spark plugs using

(Ele. 1382)

(

)

REFITTING

I - REFITTING OPERATION FOR PART
CONCERNED

Refit the spark plugs.

Torque tighten the

spark plugs (17.5 N.m)

using

the tool

(Ele. 1382)

with the

red

sleeve.

II - FINAL OPERATION

Refit:

- the scoop under the scuttle panel grille (see

Scoop

under the scuttle panel grille: Removal - Refit-
ting

) (56A, Exterior equipment),

- the wiper motor guard,

- the scuttle panel grille (see

Scuttle panel grille:

Removal - Refitting

) (56A, Exterior equipment),

- the windscreen wiper arms (see

Windscreen wip-

er arm: Removal - Refitting

) (85A, Wiping -

Washing),

- the rear and front row ignition coils (see

17A

Igni-

tion

Coils: Removal - Refitting

, page

17A-1

) ,

- the inlet manifold (see

12A

Fuel mixture

Inlet

distributor: Removal - Refitting

, page

12A-75

) ,

- the engine cover.

Special tooling required

Ele. 1382

Set of plug wrenches 16 & 21
mm torque 17.5 & 28 N.m +
square adapter 9-9.52 for
wrench Ele. 1086

Tightening torques

spark plugs

17.5 N.m

134868

«
...
1336
1337
1338
1339
1340
...
»

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands

Renault Laguna III, Manual

Search results

Summary of Contents for Laguna III

Reviews:

Brands by name

Popular brands