manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 3398

47A

-

9

SIDE OPENING ELEMENTS

Front side door: Adjustment

47A

4 - FINAL STEP FOR ADJUSTING THE FLUSH 
FITTING OF A FRONT SIDE DOOR (1st ASSEMBLY)

a

Connect the battery (see 

Battery: Removal - Refit-

ting

) (MR 415, 80A, Battery).

a

Inject wax for hollow sections into the door box sec-
tion through the wiring harness sleeve opening. Win-
dow closed.

II - ADJUSTING THE REAR SIDE DOOR 
CLEARANCES

a

Remove  the  front  wing  (see 

42A

, 

Front  upper

structure

, 

Front wing: Removal - Refitting

, page

42A-3

) .

a

Replace  the  original  indexing  studs  (

9

)  with  bolts

(

10

) , available from

 the Parts Department 

to en-

able the flush fitting to be adjusted.

a

Undo the front side door hinge bolts (

11

) .

a

Adjust the rear side door clearances.

a

Tighten the front side door hinge bolts

 (11) 

.

a

Refit the front wing (see 

42A

, 

Front upper struc-

ture

, 

Front wing: Removal - Refitting

, page 

42A-

3

) .

122797

Note:

To increase the adjustment available, enlarge the
holes on the original hinges.

After-Sales  hinges  are  supplied  with  square
slots.

122793

122783

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands