manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 2805

85A

-

9

WIPING - WASHING

Windscreen wiper mechanism: Removal - Refitting

85A

REMOVAL

I - REMOVAL PREPARATION OPERATION

a

Switch on the ignition

a

Move the wiper stalk from (0) to (1), then from (1) to
(0).

a

Switch off the ignition.

a

Disconnect the battery (see 

80A

, 

Battery

, 

Battery:

Removal - Refitting

, page 

80A-4

) .

a

Remove:

- the front wiper arms (see 

85A

, 

Wiping - Washing

,

Windscreen  wiper  arm:  Removal  -  Refitting

,

page 

85A-7

) ,

- the  scuttle  panel  grille  (see 

Scuttle panel grille:

Removal  -  Refitting

)  (MR  416,  56A,  Exterior

equipment),

- the scoop under the scuttle panel grille (see 

Scoop

under the scuttle panel grille: Removal - Refit-
ting

) (MR 416, 56A, Exterior equipment).

II - REMOVAL OPERATION FOR PART 
CONCERNED

a

Remove  the  bolts  (

1

)  from  the  windscreen  wiper

mechanism.

a

Remove the windscreen wiper mechanism.

a

Disconnect the windscreen wiper mechanism con-
nector.

REFITTING

I - REFITTING OPERATION FOR PART 
CONCERNED

a

Connect the windscreen wiper mechanism connec-
tor.

a

Refit:

- the windscreen wiper mechanism,

- the windscreen wiper mechanism bolts.

II - FINAL OPERATION.

a

Refit:

- the scoop under the scuttle panel grille (see 

Scoop

under the scuttle panel grille: Removal - Refit-
ting

) (MR 416, 56A, Exterior equipment),

- the  scuttle  panel  grille  (see 

Scuttle panel grille:

Removal  -  Refitting

)  (MR  416,  56A,  Exterior

equipment).

a

Connect the battery (see 

80A

, 

Battery

, 

Battery: Re-

moval - Refitting

, page 

80A-4

) .

Note:

The front windscreen wiper mechanism is removed
in the same way for both right-hand drive and left-
hand drive vehicles.

WARNING

To  ensure  that  the  wiper  arms  can  travel
smoothly, the wiper motor must be initialised.

125331

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands