manualshive.com logo in svg

Renault Laguna III, Manual

Share
Download
Renault Laguna III Manual Download Page 246

10A

-

169

ENGINE AND CYLINDER BLOCK ASSEMBLY

Crankshaft seal, gearbox end: Removal - Refitting

K4M

10A

REMOVAL

I - REMOVAL PREPARATION OPERATION

a

Position the vehicle on a two-post lift (see 

Vehicle:

Towing and lifting

) (02A, Lifting equipment).

a

Remove:

- the engine cover,

- the  battery  (see 

Battery:  Removal  -  Refitting

)

(80A, Battery)

- the battery tray (see 

Battery tray: Removal - Re-

fitting

) (80A, Battery),

- the air filter box (see 

12A

, 

Fuel mixture

, 

Air filter

unit: Removal - Refitting

, page 

12A-13

) ,

- the starter (see 

16A

, 

Starting - Charging

, 

Starter:

Removal - Refitting

, page 

16A-31

) ,

- the front wheels (see 

Wheel: Removal - Refitting

)

(35A, Wheels and tyres),

- the front wheel arch liners (see 

Front wheel arch

liner: Removal - Refitting

) (55A, Exterior protec-

tion),

- the engine undertray bolts,

- the engine undertray.

a

Drain  the  manual  gearbox  (see 

Manual  gearbox

oils: Draining - Filling

) (21A, Manual gearbox).

a

Remove:

- the front left-hand wheel driveshaft (see 

Front left-

hand  driveshaft:  Removal  -  Refitting

)  (29A,

Driveshafts),

- the  front  right-hand  wheel  driveshaft  (see 

Front

right-hand  driveshaft:  Removal  -  Refitting

)

(29A, Driveshafts),

- the differential output seals (see 

Differential out-

put seal: Removal - Refitting

) (21A, Manual gear-

box),

- the radiator mounting cross member (see 

Radiator

mounting cross member: Removal - Refitting

)

(41A, Front lower structure),

- the front axle subframe (see 

Front axle subframe:

Removal  -  Refitting

)  (31A,  Front  axle  compo-

nents),

- the  manual  gearbox  (see 

Manual  gearbox:  Re-

moval - Refitting

) (21A, Manual gearbox),

- the « pressure plate - disc » assembly (see 

Pres-

sure  plate  -  Disc:  Removal  -  Refitting

)  (20A,

Clutch),

- the flywheel (see 

10A

, 

Engine and cylinder block

assembly

, 

Flywheel: Removal - Refitting

, page

10A-277

) (20A, Clutch).

II - OPERATION FOR REMOVAL OF PART 
CONCERNED

a

Remove the crankshaft seal (

1

) using a screwdriver.

REFITTING

I - REFITTING PREPARATION OPERATION

a

Always replace the crankshaft seal.

Special tooling required

Mot. 1129-01

Tool  for  fitting  the  crankshaft
seal, flywheel end (80 x 100 x
8 seal).

131093

Note:

Take care not to damage the crankshaft mating
face.

Summary of Contents for Laguna III




















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands